Search results

Afternoon, put a reconditioned vcu on at the end of August, (54 plate td4) first time off the tarmac today and front wheels spinning out but nothing from the back wheels, i.e no 4wd, should note it was on a grass field on a incline, what’s your thoughts on this one gents.

[GALLERY=] Can someone tell me what this is for please, it’s currently held together with supper glue, and where i can get one?, part number? Also could it be responsible for my black smoke problem?, have checked i-cooler pipes, replaced fuel rail sensor as that was showing on code reader and...

I have just got a reconditioned vcu, it doesn't have bolt holes for the damper like my old one did, dose it matter about the damper or dose it need it?, its for a 55 plate TD4. Cheers

anyone help? Need to put new springs on rear of FL1 sport moder on a 54 plate, anyone know correct part number as rimmerbros have two, one is white and brown and the other is white and pink, any help is much appreciated.

can anyone help?, rough idle and engine trying to shake the car to bits, its ok first thing in the morning but after that it’s painful, when pulling away at junction its stugles to pick up but when it gets going it’s fine, plenty of power, have done fuel filter, lower tie bar, all plugs to...

Hi guys, can some one please tell me where the turbo solenoid valve is on a freelander 2:rolleyes:

Right i have just changed the clutch, master and slave on my 54 plate TD4, i have bled it and bled it more but the biting point is right at the bottom of the pedal can anyone sugest what might be wrong. thanks...

Hi all, heated front wind screen blows the fuse for the L/H side lights all trhe time anyone help and point me in the right direction please. the screen melted the realy in the engine compartment in december have soldered a new pre-wired one in but still pops the bloody fuse. Cheers rj75

Right chaps, having had 2 sets of drop links in about 10 months i have been looking into the cause of the problem further, it appears that the shop i have been getting them from has been suppliing the wrong ones, (gave them reg no etc, etc) there is 1 which has a 148mm long rod for up to vin YA...

Hi Chaps, how do you remove the trim along the bottom off the wind screen? do the plastic studs just popn up with a screw driver ?

anybody tryed the G force oil of ebay, is it any good or jst donky p***s, the 25ltr in 5w30 or 10w40 seems not a bad price.

Hi Guys, im trying to put up a post in the for sales section to sell some wheels and tyres, but it wont let me access it, anybody Know why ? cheers

i have a 2004 TD4, one off the headlight lenses has gone discoloured and faded is there anything i can do to sort this, or is it a new head light unit ?

Hi Chaps, FBH is starting to **** me off !. If i find the wires to the temp sensor then cut them and extend them back up to the dash to a switch, then back to temp sensor will this work ? so i can control when it comes on and off not it control me. Cheers RJ75

ok then, how much would you pay for a 5dr X reg td4, not bad over all condition, but a deep scratch on passenger door. not private from a indipendent dealer, no tradin. 100,000 on the clock. Cheers RJ75

Hi all, has anyone tried one off these , if so are they any good Cheers rj75

Hi all, ok here we go, my mates TD4 is idleing a bit irraticly not bad but is noticeable, he has had the fuel filter changed but has made no diffrence, what do you think, dodge injector ?. Also he has had the cluch master slave done twice in the last year by a garage and is still stugling to get...

When you take off the inlet manifold to clean it on the TD4 is it ok to use the same gasket again or should it be replaced ?. Thanks Rab.

Dose enyone Know what size off drain plug key is needed for the rear diff and gearbox, its on a TD4. Thanks RJ75

Can somone help please, 18cc freelander on a 05 plate, have put a new master/slave assembly on but the cluch pedal is solid, a wee bit look around and it seems that the leaver that the slave gose on to is siezed, so with the aid of a heavy hammer and a can off wd40 i have got it to move about an...