Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. S

    4.6 p38 hse - £550

    I'd snap your hand off if I wasn't so far away in Devon
  2. S

    Head gasket choice with skimmed heas

    RAVE state heads should not be skimmed as when new the aluminium heads were impregnated to seal any porosity. If they are not re impregnated after a skim the head gasket lasts a lot less miles. There is a company in Manchester who can impregnate castings for the public. I found this out from...
  3. S

    D2 Facelift Headlights stolen too.

    It may be worth using these alpha dots. Alpha Dot - The UK's Number One Security Marking System
  4. S

    Seat squab

    Check with Ford as they are the same seats as in my Mondeo. You may be able to get one from a breaker as well.
  5. S

    EGR.. Should have done it ages ago.

    Inlet manifold isn't hard but is a pain in the arse as space is limited.
  6. S

    Re mapping

    Mike will come to you, he's often in the south west.
  7. S

    change head gasket

    I've just done my gasket and changed the head for a new one from Turner Eng. Changing the gasket is easy, it's the removal of manifolds etc that is the pain. I'd also recommend an engine crane as it is very awkward getting the head in and out due to its weight and the engine being on an angle.
  8. S

    locked out of my disco

    I'm sure car thieves don't need to look on a public forum on how to get into a Disco especially when some are driving away new Audis and BMW's for a pastime without they keys or fobs.
  9. S

    Air-con noise from pulley

    sounds like you need a new pump to me.
  10. S

    Air-con noise from pulley

    I would reckon a new pump. I had this recently on my Jag XKR. The pulley on that was on some magnetic clutch and I just purchased a good second hand unit. Remove the belt and see if there is any play in the pulley.
  11. S

    No turbo boost in my TD5 Ideas???

    I agree with Johnlad, the wastegate is easy to check and should have been done by your mechanic, or try a modulator. Whats the intercooler looking like ? It may have gone pop.
  12. S

    Need a new cylinder head :-(

    Yours will be a 16P head. I would recommend Turner Engineering. I recently bought a new AMC head from them.
  13. S

    Td5 head type

    I just bought a new head from Turner Engineering and would recommend them. You need to look at the gasket you have just taken off and replace it with one with the same number of holes. Mine was a 1 hole gasket and I replaced with like for like.
  14. S

    Fitting a camshaft to new head

    Many thanks gents. Fitted the camshaft and carrier tonight with no problems. Thanks for the advice.
  15. S

    Fitting a camshaft to new head

    Thanks very much. I 'll give it a go tomorrow.I've put the lash adjusters in the vice and it certainly has helped although it's still sitting high at one end. Thanks
  16. S

    Inlet/Exhaust Manifold gasket replacing

    You sure it was the turbo whistling and not a warped exhaust manifold?
  17. S

    Fitting a camshaft to new head

    Hi, Just after some advice. i've bought a new head from Turners as my existing one is knackered. The turners head comes with the valves already fitted. (My car is a TD5 2003 16P engine) I'm in the process of moving everything over from my old head and have trial fitted the camshaft...
  18. S

    td5 exhaust manifold

    Thanks for this, I'm about to use your guide to do mine! Hope yours is now sorted out.
  19. S

    Sunroof Motor

    Fuse or new switch
  20. S

    best tyres and size?

    Ideal, thanks for the quick reply.
Back
Top