TD5 extension loom - making my own

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
BIG_GINGA_BEARD said:
Do you reckon you could make your own loom from say this:

Land Rover Defender 110 02 Onwards Td5 Chassi Loom | eBay

Way too expensive to buy one from a company.

Thought about having a go at building my own.

Comments
Click to expand...


If you mean an extension to the TD5 Engine ECU loom, then no. The ECU Connectors are on the Main Harness, not the Chassis Harness.

The Chassis Harness runs from the engine side of the bulkhead, down though the O/S chassis rail and exits out at the back for the rear lights, fuel tank, etc...


The ECU Connectors are AMP Econoseal, but I've only ever seen the Black one for sale, never the Red one. I don't know if they're keyed differently, or if they're interchangeable.

Another drawback is that the Male connector is only available as a PCB Header.

The Black Connector is available from Polevolt - ECU Connectors: Polevolt Ltd

Female Connector
ECU36-400.jpg



Male Connector
ECU36PCB-195.jpg


ECU36PCB-550.jpg


.
 
What exactly do you mean?

I'm not familiar with the td5, I don't know where the ecu is or where you would want to extend it to.
 
mundungus said:
What exactly do you mean?

I'm not familiar with the td5, I don't know where the ecu is or where you would want to extend it to.
Click to expand...

Basically i have a TD5 fender and the ECU is under the drivers seat. I wouldnt mind moving it out of harms way. So the idea was to extend the ecu cables in and out of the ecu so i can move it.

ratty said:
PM The Mad Hat Man.

He should be able to make you an extended loom. BOTH cables..... and a waterproof box is required.
Click to expand...

I did that a while ago ratty, there a massive saving on the manufacturers ones but there still £200 odd quid.

I was just wondering if i could make me own to save the cost.

As pointed out by PaulMc though it appears to be a non starter. :(

Nevermind, just an idea
 
So your not brave enought to cut one wire at a time,solder in & heat shrink a new piece of wire, until all 1 billion wires are extended.
Must admit I'm tempted to do it myself, but holy s*** if it doesn't run.

What about an auto sparky, can they get ecu plugs. You must be able get the plugs seeing as you can buy the leads.
 
BGB instead of extending loom how about making a water proof box for ecu to sit in.
I have been thinking about it and might now give it some more thought
 
My company sells a TD5 extension cable that terminates in an IP6 rated box - but yu better take out a mortgage - they is feckin expensive!

ask Bucky for pics - he has one.
 
Last edited:
yu cant have a completely sealed box, because the ECM has to breathe. If it is sited well , it will stop water sufficiently till yu get thru the wet stuff.
to be honest, if yu mount it on a rear bulkhead (like Bucky), by the time the water covers the box, yu are in deep doodoo and wanting breathing apparatus. :rolleyes:

31815d1336763824-td5-extension-loom-making-my-own-buckshot4-1.jpg
 

Attachments

  • P6280107-sml.JPG
    P6280107-sml.JPG
    46.2 KB · Views: 4,154
  • buckshot4-1.JPG
    buckshot4-1.JPG
    78.9 KB · Views: 2,127
Last edited:
You must log in or register to reply here.

Similar threads

A
Combusting wires - one big FUBAR
Replies
7
Views
1K
amsthenovice
A
B
muck in the frame
Replies
4
Views
803
lynall
L
L
Newcastle mech recommendation?
Replies
8
Views
777
neilp1
N
H
TD5 discovery series 2 engine problem
Replies
2
Views
436
Stanleysteamer
Stanleysteamer
T
td5 engine power loss
Replies
9
Views
2K
Brown
Brown
Back
Top