SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
What pipe fittings are on the land rover discovery 1 3.9 v8... are they quarter inch.
Supply and feed pipe fitting diameter
- Thread starter SnowmanV8
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
What pipes?
SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
Fuel supply and return pipes.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
they're 1/2 nuts on my carbs and 1/4 pipes
robint
Well-Known Member
- Posts
- 7,057
4" sewer pipe push fit
blue beasty
Leaks an prone to bits dropping off
- Posts
- 61,275
- Location
- Gloucestercotshirewolds
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Sewer pipe is 10.16cm in new money 
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
Mines a v8 not , 300tdi.
Last edited:
SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
Are the 3.9 v8's , fuel system e.g. pipes the same as the 300tdi
lorri789
Well-Known Member
- Posts
- 4,657
- Location
- West Stirlingshire
5/16
8mm
???
8mm
???
dazj
Member
- Posts
- 13
- Location
- Winscombe, Somerset
ok, the fuel pipe is 8mm, thats fine, but the fuel sender unit has two pipes, 1x feed 1x return. are these 1/4" BSP? does anyone have a definate answer? even landrover UK wont tell me? bar stewards
SnowmanV8
Well-Known Member
- Posts
- 3,938
- Location
- Portishead, Near Bristol
Uh oh me in-laws arrived
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
maybe he should go introduce himself
dazj
Member
- Posts
- 13
- Location
- Winscombe, Somerset
Hello Dr Evil,
im darren, snowmans to be father in law. i introduced him to landies, Ive had several, and they have all been fun.
im darren, snowmans to be father in law. i introduced him to landies, Ive had several, and they have all been fun.
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Mr Noisy
Coming in your ears.
- Posts
- 10,146
- Location
- Altrincham, Cheshire
the fuel pipe fittings are on odd thread, definitely not bsp.
i replaced all my steel pipes with rubber hose, and terminated the hose with hose tails that i think were at 3/8 bsp but these were to join to some male-male adaptors, the other end of which i do not know the thread of.
not a common thread though otherwise the hydraulics shop i went to which had racks of fittings up to the ceiling would have had the hose tails in a direct fit thread.
hth.
i replaced all my steel pipes with rubber hose, and terminated the hose with hose tails that i think were at 3/8 bsp but these were to join to some male-male adaptors, the other end of which i do not know the thread of.
not a common thread though otherwise the hydraulics shop i went to which had racks of fittings up to the ceiling would have had the hose tails in a direct fit thread.
hth.
