3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
This might need to go in the daft question section, but....
Is there a PTO facility on the P38 manual gearbox?
Cheers
Is there a PTO facility on the P38 manual gearbox?
Cheers
Power Take Off
- Thread starter 3extruckers
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
jamesmartin
Well-Known Member
- Posts
- 91,879
- Location
- louth lincs
no ,none at all
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
Thanks.
Plan B then...
Plan B then...
easye1
Banned
- Posts
- 8,557
twizzle
Active Member
- Posts
- 159
- Location
- edge of winchester
make you own using a hydrolick pump to motor
- Posts
- 7,332
- Location
- Under my landy
drive through rear axle with PTO on the back of it?
Oh... and... some jacks so the back wheels are off the ground
Oh... and... some jacks so the back wheels are off the ground
easye1
Banned
- Posts
- 8,557
drive through rear axle with PTO on the back of it?
Oh... and... some jacks so the back wheels are off the ground
OR, jack one wheel up, replace wheel with just a rim,
then run a drive belt from rim to power your wtf you need powering.
(will 1 wheel in the air work on a rangie?)
it worked in the "waltons"....:bolt:
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
I shall try fix a pump where the air-con compressor was then...
Spunka
New Member
- Posts
- 2,247
- Location
- Nr Wakefield
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
I want to put a hydraulic pump on. I'd have to try and mate it up with one of those electric clutches.
Cheers
Cheers
- Posts
- 7,332
- Location
- Under my landy
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
That's what I was thinking. Mate that up with an electronic clutch so it's only pumping when i switch it on.
easye1
Banned
- Posts
- 8,557
him no say
me think man want to fit a low /hi look custom hydrulic
suspenders...
but might just want to run a concrete breaker instead
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
Sorry Spunka,
I want to use it for an hydraulic winch. I had one on my old S11A before i sold it and as easye1 says, if i run a flow / return from the two block spool valve i can run all sorts from it.
Cheers
I want to use it for an hydraulic winch. I had one on my old S11A before i sold it and as easye1 says, if i run a flow / return from the two block spool valve i can run all sorts from it.
Cheers
- Posts
- 83,232
- Location
- Embasinga stocæ
pas pump?
3extruckers
Active Member
- Posts
- 216
- Location
- West Yorkshire
Thought about that, but it'd be running all the time.
Has anyone used one for anything like that successfully before ?
Cheers
Has anyone used one for anything like that successfully before ?
Cheers
- Posts
- 83,232
- Location
- Embasinga stocæ
all yu need is a valve to short circuit the system when not being used. they are used to be on all the time.
ratty
I'm not special I'm limited edition
- Posts
- 34,277
What's wrong with using the electro hydraulic power pack from a tipper or recovery spec lift? It's the pump, solenoids and tank all in one compact unit.
