freelander td4 2002 steering shake when going uphill?

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
F

frenchdave

Member
Posts
15
Location
france
My freelander td4 manual gearbox year 2002 with 150k miles. It has a problem which started today. When accelerating uphill at 30mph the steering wheel shakes about 1 inch . this stops when on the flat. I have put it on a two post lift, and all wheel bearings seem fine. There is slight play in the front driveshafts, but no different than i have felt in the 5 years I have owned it. The propshaft when twisted seems to have a slight clunk at the engine end. also the rubber donut type bushes have play up and down, which I think is just on the edge of being ok. Could failure of the propshaft bearing and rubber cause this steering shake? any ideas on what to try?
I could take the propshaft off and drive it in 2 wheel drive to see if this stops?
is this a good idea
Cheers for your respones
 
Lower tie bar has probably gone soft, coupled with the inner drive shaft joints stiffening under load due to wear.
 
An inch of movement on the steering wheel is a huge amount of travel!

Has the steering wheel adjustment lock lever been locked undone or summat?

As the steering wheel is connected to a shaft, split with a UJ, to the steering rack - and that is bolted to the bulk head. I'm not sure how the engine/box/IRD floating around could cause that amount of travel in steering wheel.

Or are you talking an inch of rotation movement?

I'd suggest doing a 1 wheel up test.

www.landyzone.co.uk

Tests new Freelander 1 owners should do on their car

These points have been written so many times, I just want to put them in a thread by themselves so a link can be used rather than typing them out each time! This relates only to Freelander 1 vehicles. Freelander like all cars can have many different faults. Lights can stop working, leaks can...
www.landyzone.co.uk www.landyzone.co.uk

Its been proven that on a level wheel speed rotation front to back may be the same (given tyre conditions), accelerating up hill the axles want to turn at different speeds. If you're VCU is stiff, this will cause wind up and problems.

I'd have thought if this were a problem, it would gradually increase though, not jump straight to such a major symptom. Mind you, that is also the same with something like the lower tie bar.
 
Its a shake side to side on uphill acceleration. I first thought drive shafts, but the idea that its the engine mount tie rod sounds more likely. I brought a MGZT cdti a few years ago, had similar issues at anything above 40 mph. The rear lower tie rod bushes were shot. A new one with poly bushes sorted it and lasted the car till it died. So for £30 will try that first.
 
Not so good just a few weeks after fitting the new tie rod , the problem of knocking under load has returned. It sounds like a metal pipe or rod is banging against the underside.had it up on a lift, and cannot find anything loose. Also steering has a shake at the same time as the banging. Front drive shafts maybe?? they have a small amount of play but no different from when I checked them 3 months ago. Any ideas please
 
frenchdave said:
Not so good just a few weeks after fitting the new tie rod , the problem of knocking under load has returned. It sounds like a metal pipe or rod is banging against the underside.had it up on a lift, and cannot find anything loose. Also steering has a shake at the same time as the banging. Front drive shafts maybe?? they have a small amount of play but no different from when I checked them 3 months ago. Any ideas please
Click to expand...
Just seen this.

Mine does this so i bought one of those tie rods. I bought the same KKH102260.

Took the old one off, put the new one on and exactly the same but slightly less vibration. Under load, engine would move back and a bracket would tap the subframe.

Turns out TD4's have a longer one to push the engine further away from the subframe. (KKH000070)

My idea is to get a broken one from a breaker and push in new bushes from new shorter bar.
If you haven't thrown away your old part, you may have the same problem

Hopefully that will solve my problem when i get round to it.
 
You must log in or register to reply here.

Similar threads

eduard_andrei
Noises from behind when full steering
2
Replies
21
Views
1K
GrumpyGel
GrumpyGel
B
vibration under load.
Replies
1
Views
621
andyfreelandy
andyfreelandy
N
Freelander 2 (LR2) Drumming noise when steering right
Replies
8
Views
432
Nathon91
N
PaulN
Freelander TD4 Juddering at 60mph and 2500rpm?
Replies
7
Views
618
PaulN
PaulN
B
Freelander TD4 Mk1 Rear Diff - Does anyone have any advice on how to replace the rear diff?
Replies
1
Views
343
Freddie17
Freddie17
Back
Top