Search results

cheers mike got some of that il give it a wire brush and waxoil it. I saw how much is connected to it. Big job that would be to swap one out all the ones for sale look rusty as ****

Freelander 1999 station wagon 2.0 d Dropped the sub frame down its on the rear passenger side its rotted all the way round the rear tube just before where the bolt goes in, once it was dropped the above metal is fine. Its very odd i was expecting to find allsorts of nightmares thinking maybe it...

This shows the location of the Temp sensor that controls the fan and im assuming talks to the ecu this photo below shows the temperature transmitter that links to your temp guage on the dashboard. I have taken out the wire so you can see better its directly below the temp sensor with one...

Cheers Nodge you're loads more use than my Haynes manual thanks.

thanks Nodge. There are two water sensors on the thermostat top one two pin i disconected and it turns the fan on so im saying thats working. My mate run a wire from battery to the lower sensor and the gauge went up so im changing that one a 1 wire one. Maybe that will help someone else if...

freelander 1 - 2.0 l series diesel Noticed yesterday when i had gone on a reasonable run that my water temp guage was only on 1/3 oposed to the usual half way that it always gets to and never moves from. Today went on a shorter run and noticed that the temp guage didnt even move up Does this...

I took off the old one the big bush just fell out was completely gone. I put the new one on and then took out the two bolts on the tierod bracket that connects to the engine. Put some thread lock in and tightened up and its been fine since. changing that bottom bracket has obviously fixed a bit...

Hello had a knocking when turning right and when it was in for the MOT and up on the ramp i could see the roll bar was off center and you could see where it had been fouling the support strutt. Garage said it was the roll bar had rusted away which once it was off was clear it had worn the bar...

Hello guys went off to work today and noticed a clunking when changing gear, got under it and realised by bottom tie rod bracket was loose. Tightened it up and its ok bit of vibration through the cab on tick over. Do you think the tie rod bushes could be worn and the vibration has loosened the...

both front driveshafts, new calipers, discs and pads 198k miles l-series

your saying you only have to block off the inlet manifold one and the exhaust one isnt nessesary and you can leave it as is

I am just looking to do this EGR Blanks on an lseries. Am i correct in thinking that you remove the actual unit? The upper one seems simple to take off (first pic), the lower one (second pic) however looks like right pig its proper rusted up onto the exaust looks like il have to drill them out...

thats for the hydo mount main mountain like nodge says top and bottom are stabalisers and not holding must weight so as far as I found they were just take of and put back on

This one was really easy first take the top tie bar off the mount one bolt 15mm Then push it up out of the way Then put a peice of wood under the engine and jack it to take the weight then get an 18mm socket and loosen the bolt on top of the mount take the nut off jack the engine over the...

https://www.landyzone.co.uk/land-rover/freelander-1-vibration-got-me-baffled.230569/#post-2649516

i would say its your driveshafts mine are due changing i have been doing other stuff as they are not that bad, I might have a search about driveshafts on here theres probably someone with the same issue fixed mine is better but still if I am in 4th low revs it does vibrate through the car not...

Hello Joe iv got the same car, I would check your driveshafts and also check your engine mounts, if you are confident your vcu is fine, im not sure much about if your VCU is on its way out it might give a vibration under strain but sure someone else with advise on that. Engine mounts The one...

Upper tie rod to engine mount KKH101900 You need a 15mm socket small and an open ended spanner long as you have Theres a support bracket with 4 bolts that connects to the chassis in all four points but also at the top when the bolt goes through the bush, all of the bolts apart from the bottom...

I had this issue about a year or so ago and it was the matrix, not sure if anyone has suggested this but if you get some white tissue paper blot the liquid and see if its coolant colour if not its your seals. I had a look a a few how to things on doing it and it looked like a right **** of a...

This is the one thats broken