Search results

Does anyone know what size SCHRADER VALVE the Rangie uses as mine leaks from the fill point valve? I don't want to fork out £50 for a vlave kit just for a 10p valve...

Here is a cute little baby I had a look at the other day, on its way to being someones treasure. Visit to Sussex Autogas Systems « Kirdford Village

Ok I have scanned the threads on loss of power, but can't find one that seems to replicate my fault. 05 plate TD4 Will drive perfectly for about 20 min, then the power drops and it doesn't matter what gear you are in she is labouring. Stop, turn off ignition, turn her back on again and she is...

Came out of Tesco's this afternoon and noticed a ticking noise, thought "damn, another blooming prop shaft bearing", got a couple of hundred yards down the road and bang, nasty low end rumble, so immediately stopped the engine - had it recovered to the garage. It is definitely the big end -...

OK so it is getting to that dark time of year, and I decided to stick some driving lights on the bull bar. I didn't realise it when I bought them, but they have LED rims round the outside, so would like to have them on all the time, so the question is... 1) Does anyone have a good way of...

Got a high pitch buzz from my speakers (1997 4.6 HSE) in line with the revs of the engine - turn the radio on and it is ok, then after a minute or two, the buzz starts and slowly gets louder, turn the radio off and back on and it goes away for a couple on minutes - do you think it is the head...

Just thought I would give my experiences with my new Archos 5 Internet Tablet... I bought one of these because I am flying each week so wanted to put my films on something, but it does sooo much more... It has NDRIVE sat nav built in, and as my Tom Tom is on it's way out I decided to try the...

Rangie Ville Look aftereach others Range Rovers - wash and polish. Trade prop shafts. Get extra points for adding a friend - buy an engine Buy lube and gaskets. If you don't keep looking after the girl the BECM will loose sink and she rusts.. I reckon it's a goer :D:D:D

OK - need some assistance here guys - the air con has stopped working... Put the Faultmate on her, no faults on the HEVAC - the system has the air con swichted on - but the clutch is not engaging. Tested the solenoid on the the compressor clutch and that works (hot wired it to a battery), so...

You fix onething then something else breaks... Took the steering wheel apart to see if I could find an earth fault that is stopping my cruise control working (funning voltage reading on the set button) - of course to do this you have to disable the SRS, RAVE said to disconnect the battery...

Driving home tonight, thought I would boot it on a nice hill straight - little bit of wheel wobble then it started chirping squeeking noice - best described as a very loud bird stuck in the grill.... Not breaks as still chirps when breaking Not belt cos you can rev engine and no noise coming...

Cleared all the faults down on my HEVAC and the only one still showing is Evaporator temperature sensor to ground - it is actually registering 65000 degrees. This is the only part I did NOT buy when I prepared to replace the blend motors :doh: I cannot find the part at Rimmer Bros or Island...

I took posetion of a shiny new MSV2 Faultmate today - after all the too ing a fro ing to get it licenced etc. I settled down this evening to start REALLY seeing what might be wrong with the car. I got it to talk to the HEVAC and the Suspension, but that was all - everything else came up with...

Went to the garage this morning to fill up on gas - turned the car off outside the gates (waiting for them to open) - went to start her up and nothing - engine light on all electrics on but wouldn't start... Matr came out (with trailer) to help/recover me - quick short of the starter...

My P38 rear door rubber/seal is coming off :mad: I have had a look and it seems to have come away from the plactic clips that clip into the door i.e. the clips are still in the door. I don't think I can get the clips out without breaking them. Can you get new clips or is it a new seal...

OK I have replaced the two short pipes to the pump and actuator (?) and I have replaced the switch on the brake pedal - I have looked at the long pipe but cannot see and cracks etc. - yet when I take the actuator pipe off and blow down it I can't creat any pressure - therefore surmise that a...

OK - Here are the facts 1997 P38 HSE Had the car two weeks Pasenger side footwell bone dry until I get inyo it this morning - big puddle Can feel wet on LH side of cover behind glove box Where do I start - BTW run out of matches

I was wondering if I had missed something cos he has put a Rangie up on the For Sale board :eek:

I have a rattly drivers door, so I need to adjust this. I can see it is adjusted by the plate on the door post, this has two torx screws in it - one looks to be 'abused' already. Am I setting myself up for some grief - I assume the screws are nicely rusted in place and the reason one is...

I went to replace the pollen filters on the newly aquired 4.6HSE yesterday. Good grief, I didn't believe the amount of crud in there, it was jam packed between the filter and the inlet, leaves, twigs, grass, a veritable compost heap. I couldn't get the filters out without dropping stuff into...