Search results

"Hi all, its been a while. So, a year or so ago I got fed up with my life and job on Nassau and finally decided to do something. I sold my studio and just about everything in it, sold my house and most of my vehicles. Quit my job of 36 years and moved to Abaco. Abaco is a chain of islands in...

Hi all, Been a while since I posted but still here and still loving my 90. Question. I am changing both dumb irons this weekend because of rust. Any tips? or anything special I should know? Thanks.

I changed my clutch a few moths ago, it has been making noise ever since. When I received the clutch and took it out of the box the springs were making lots of noise, it seemed like they were too loose? Is it normal for the springs to be noisy? Also, I think my mechanic did a not so good...

I am trying to find a part for my transfer case (1998 300tdi). The part is to do with the shifter. Does anyone have an exploded picture of my transfer case?

When I put the vehicle in neutral and take my foot off the clutch I am getting a loud rattle. I have just replaced the entire clutch and installed an Ashcroft gear box. What have I done wrong?

How do I tell if the Diff Loc is engaged without depending on the diff loc light in the dash? Thanks

My Ashcroft gear box arrived and it is very purdy indeed. I will be installing it next week. Any tips at all for installation? Oil? anything at all. Thanks.

What has to be removed? When we did my clutch, the bell housing, gearbox, transfer case all came out with the fuel tank. Will all this have to be removed again? Thanks

My gear box is done. No chance of getting a proper trustworthy rebuild in the Bahamas so I have to replace. I would hate to have to send the core back as it would cost a fortune. What are my options on getting a good gearbox for my 1998 300tdi/90 ? Thanks.

I recently changed my clutch, so I had to remove everything from the bell housing back. After I installed the clutch and put it all back together, I also changed the fluid in the gear box. I used ATF. Then my gear box started to leak !. My mechanic has looked at it twice now and swears...

1998 300tdi R380 gear box. I am missing a bolt out of my bell housing, does anyone know what size/thread/length they are? Thanks.

What does Land Rover say? What do you say? I needs to know. Thanks

I need to purchase copper drain plug washers. I am in The Bahamas and there are no LR Dealers. How can I find the size copper washers needed for the gearbox, transfer case, engine and fuel tank? Thanks.

My gear box seems to be getting more difficult to change gears, "Notchy". It feels like its getting harder to get into 1st and reverse,sometimes 3rd. It does not always happen and seems to be more noticeable when she is cold. Thoughts? Thanks.

Not sure if that is what the part is called but it is really badly rusted. This is the part of the chassis that runs from on chassis rail to the other and the Ball Joint assembly is mounted to it. This cross member looks like it is part of the chassis being welded directly to the rails (I...

So, I ordered a new clutch kit and fork. I am also installing a new cross member for the transfer case so I already had the cross member and the fuel tank out. So I figured seeing that all of that is out I can install the clutch from the bottom, lots of space. Disconnected everything...

I am changing my clutch this weekend. Any words of wisdom? Thanks

I am changing the clutch in my 300tdi. The place that I ordered the clutch from does not carry a pilot shaft for installation. Where can I get one or what can I use? Thanks

I was underneath my 90 looking for a noise:) And noticed at both ends of the support for the transfer case that goes from one chassis rail to the other is really badly rusted, really bad. It has to be replaced. It looks like it un-bolts? Is it that simple? And what is the part #, I looked at...

Both of my dumb irons are quite rusty and I want to change them. What is involved? Any tips, advice or videos........................ Thanks.