Search results

Needed low ratio so selected neutral and moved to low. A few beeps and Select Neutral was permanently displayed. I still had High ratio so drove home to loads of beeps (lucky it wasn't a long way). To cut a long story short the problem was the XYZ switch. The switch had seized solid so when...

Stay Cool is suposed to help prevention of overheating. Apparently it gives improved heat transfer, making a faster warm up and better coolig - up to 15 deg. C reduction in engine operating temperature.

Anyone in Denmark (Jutland) with Hawkeye to helpwith a 2001 Freelander 1 TD4 with the three amigoes lights that need a reset.

L322 - Car is 2005 diesel Range Rover with the can boot loader message showing. No radio or sat/nav. Have replaced the Denso unit purchased a 2015 nav disk and YIA500010 recovery disk followed the instructions from the Service Bulletin but no joy. Have tried several times. Had battery charger on...

The part number on a headlight is XBC 104180 I can't find it on the UK parts manual. Can anyone help it may be from overseas? Cheers

Helping someone. Diesel fuel filter housing wiring? There is a small wiring block with three push in wires, does anyone know which position these should. I think they are for the pre-heater. I don't have rave with me I am miles from home. Also how do you remove the 90 degree fuel pipes...

Just watched a Utube video on fitting some aftermarket propshafts to a heavily modded Defender. The point made was that the slider of each propshaft should be to the front of the car. So on a P38 the rear propshaft slider would be close to the transfer gearbox flange and at the front the...

Anyone tried TyrePal? checks your tyre pressures every six seconds. Advertised a lot so they must be selling a few.

Can anyone let me have the part number for the fuel feed pipe from the rear of the injector rail to pump on a Thor 4litre V8 circa 1998?

Anyone know of a 4.6 Thore p38 recently or about to be broken up?? I need the fuel feed pipe from the back of the injector rail to the pump. Have tried over thirty on-line and off line companies so far including all over Europe and the States but no one has any in stock. So second hand is only...

The Thor (4.6 Year 2000 p38) petrol fuel feed pipe no longer available WJP108240. This is the motronic fuel system using one pipe from pump to rear of injector rail and no return. I was returning from Scotland when the connector on the fuel rail let go!! loads of fuel all over the rear of the...

Anyone know what price to expect for a scrap catalytic converter, p38 petrol?

Got an SRS failure on the message board. This happened a few days after I had moved the passenger seat back for an elderly person (6 foot six!!). So I thought the problem would be the stupid connectors under the seat, but no amount of pushing and pulling had no effect. So got the TestBook out...

Seen a very interesting post on another site about replacing ALL the interior bulbs for LED's. Main benefit is better light output which would be good as the standard lamps are very poor and not up to modern standards. Also, half the battery consumption! which would be very helpful as anybody...

Whats the best emergency kit for the snow?? (something special?)

Flex plate gone on my 4.6 Thor. Any tips would be welcome

Car 4.6 2000 Thore engine. Can anyone give me the part number for the rather long air conditioning pipe (the thicker one) that goes from the bulkhead round the side of the engine bay, behind the air suspension block and with a short length of flexible up into the air/con pump. The flexible part...

Many members say run in at + 1500 ie 2000 revs for 20 minutes. Seems to make sense as the block would be fully warm and anything over 1500 revs would supply good, if you could call it that oil pressure to lube everything in sight. Where does this info come from. The workshop manual just says...

The timing chain on the V8 has a standard part number ERC7929 But apparently comes in two versions under the same part number, floppy or stiff. Has anyone experience of fitting either ? I am in the process of changing mine but on fitting the new chain it seemed a bit floppy had quite a bit of...

Darn it! After 156,000 miles the camshaft on my 2000 4.6v8 needs replacing, getting a missfire. I fitted recon heads about 10,000 miles ago and because they were skimmed etc have decided to use a set of adjustable pushrods with the standard new camshaft and hydraulic lifters. It was a real pain...