- Posts
- 31,372
- Location
- North Shropshire
Last edited:
What did you do with your Range Rover today
- Thread starter Dopey
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
brianp38dse
Well-Known Member
- Posts
- 19,582
- Location
- heathrow
- Posts
- 4,452
- Location
- Rotherham
Me tooi like pics
- Posts
- 4,452
- Location
- Rotherham
- Posts
- 5,692
- Location
- North Manchester
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 5,692
- Location
- North Manchester
Don't forget to take yourself in hand
Not while I'm under the L322 sorting my nipples out shirley
- Posts
- 5,692
- Location
- North Manchester
OOh just noticed I was on 2,999 posts
300bhp/ton
Well-Known Member
- Posts
- 4,733
- Location
- Near MK
Trying out my new pressure washer. It scrubs up pretty well, not perfect by a long shot mind.
It did get a bit dirty the other day flinging mud everywhere.
It did get a bit dirty the other day flinging mud everywhere.
Made a P38 friend at work. I shall call him Sebastian. Walking back to my bus and see him pulling up. Some highly decorated navy officer. Naturally I hit him with "nice car, sir." To which he says "not as nice as yours."
So that's it, friends for life. Me and Sebastian.
So that's it, friends for life. Me and Sebastian.
Datatek
Well-Known Member
- Posts
- 43,930
- Location
- Near Poitiers SW France
I have an HP24, just don't fancy the job of fitting itAnother issue with the Hp22 is wear on the stator shaft this explains the common problem with the trans losing forward movement during an emission test with Diesel P38s they rev the engine to redline during the test. if the stator shaft and sealing rings are worn, running the engine at above 2,000 rpm in Park or in Neutral lets the converter oil partially apply forward clutch which is the A clutch drum, instantly destroying it. The quick thinkers at ZF fitted hardened shafts to the HP24..
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
I was there onceOOh just noticed I was on 2,999 posts
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
I wouldn't fancy iteither unless I had a pit or lift available!I have an HP24, just don't fancy the job of fitting it
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Grovelling or what.Made a P38 friend at work. I shall call him Sebastian. Walking back to my bus and see him pulling up. Some highly decorated navy officer. Naturally I hit him with "nice car, sir." To which he says "not as nice as yours."
So that's it, friends for life. Me and Sebastian.
View attachment 249829
Datatek
Well-Known Member
- Posts
- 43,930
- Location
- Near Poitiers SW France
I have a shallow pit but having dropped the gearbox, I'm not sure how I would get it out from under the car. I'll have to bite the bullet and do one day.
Henry_b
Think outside, no box required.
- Posts
- 15,353
- Location
- somewhere else
Might be better to do it on the ground with her on axle stands, you can get some good height..
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Think motorbike lift with wheels was the recommended tool as long as you have a flat surface for it to roll on.
