discoboy84
New Member
- Posts
- 537
- Location
- Ipswich
how much do you guys reacon it'll cost to repair O/S inner wing and battery tray on my disco
my welder charges £25 an hour?
my welder charges £25 an hour?
Typical cost to repair inner wing
- Thread starter discoboy84
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 83,296
- Location
- Embasinga stocæ
how much is a year and a half?
V8_Disco
New Member
- Posts
- 1,180
- Location
- Shropshire
a bit more info might be uselfull
andyb66
Well-Known Member
- Posts
- 1,795
- Location
- Middle of Salisbury Plain, Wiltshire
Does depend on how much rust there is, do you want a replacement panel or a patch up job.
Last 'patch up job' I did, was about £150-ish a side for inner wings, battery box, footwell and around front lights.
![[JP]](/data/avatars/m/29/29578.jpg?1437394565){kind=avatar}
[JP]
New Member
- Posts
- 3,980
- Location
- Newbury, Berks
After spending 2 months welding loads of rust on my disco and doing the inner wings, if I had to do it again, I would charge 300quid! lol
si844
New Member
- Posts
- 368
- Location
- Southport, North-west
it cost me £40 for secondhand mig welder and £10 for sheet steel. i needed to do the inner wings on my vauxhall few years ago, with no experience at all. was good enough for mot. after a bit of practise my disco wings look quite good.
vivnap
Banned
- Posts
- 2,610
- Location
- south normanton
si844
New Member
- Posts
- 368
- Location
- Southport, North-west
tis a nice tidy job that is vivnap
Beast o Bodmin
Banned
- Posts
- 17,157
[JP];930608 said:
found some a-pillar replacement bottoms .lower hinge area.Do you want?
Shed is clearer too...
Beast o Bodmin
Banned
- Posts
- 17,157
easier to wack in new inners lagged with oil.
vivnap
Banned
- Posts
- 2,610
- Location
- south normanton
thanks, dont like bodge jobs
this discovery has been given a right good going over, reckon its now one of the better ones
new inner and outer sills both sides, new boot floor every bit of rot i could find cut out and welded using new panels.
Attachments
trax99
Well-Known Member
- Posts
- 1,149
- Location
- Montgomeryshire
Sweet,
thought I'd done a tidy job but yours is much nicer
thought I'd done a tidy job but yours is much nicer
trax99
Well-Known Member
- Posts
- 1,149
- Location
- Montgomeryshire
As for you discoboy, i reckon your best bet is to pick up a mig and get a new inner wing/battery tray panel - i got mine from YRM metal solutions on ebay, pretty cheap ( £60 ish) for both wings and went in with minimal trimming, only had to learn to puddle weld as well (yay !!)
discoboy84
New Member
- Posts
- 537
- Location
- Ipswich
i have a MIG (gasless crap) need some pratice and yes YRM is looking like the place for a whole inner wing, i need a battery tray too though
si844
New Member
- Posts
- 368
- Location
- Southport, North-west
thats wot i got too, does the job tho - just. (easy to burn through metal as theres hardly any adjustment).
i'v patched up quite a few inner wings, battery trays, boot floors, and exhausts with mine.
thebiglad
Well-Known Member
- Posts
- 7,387
- Location
- Central France
thanks, dont like bodge jobs
this discovery has been given a right good going over, reckon its now one of the better ones
new inner and outer sills both sides, new boot floor every bit of rot i could find cut out and welded using new panels.
Hi vivnap, you've done some real quality work on that Disco, especially the front end battery tray area, very nice indeed. You must be pleased with that?
- Posts
- 83,296
- Location
- Embasinga stocæ
vivnap
Banned
- Posts
- 2,610
- Location
- south normanton
yea im pleased with it but if i was doing it inside a workshop i could have made a lot better job of it. i wont have a workshop untill later on next year when i get it built
working out doors isnt the ideal way to do repair work cos the british weather just isnt on your side
