- Posts
- 12,223
- Location
- Sud ouest France !
sh&t, you got serious!
number one on the list and he was rendered unconscious ...
No throttle response P38 Range Rover after injector pump reinstall
- Thread starter Kelvin'D-MiC'
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
number one on the list and he was rendered unconscious ...
- Posts
- 18,999
- Location
- Buckinghamshire, UK. ('95 DT)
First time we've lost a member halfway through their first post.
- Posts
- 12,223
- Location
- Sud ouest France !
I concur grrrrrrr-rrr, its almost like those magazine stories from the seventies about people self combusting and disappearing into wardrobes......oh, hang on that's f#cking Narnia.;
- Posts
- 12,223
- Location
- Sud ouest France !
not the persuader then?
- Posts
- 12,223
- Location
- Sud ouest France !
now that has to mean fly off? im going to bed...
later peeps.
later peeps.
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
I own a P38 Range Rover manual Diesel 95 model. I had been struggling with a leaking injector pump and it removed for service and had put back in and after running the car a couple of weeks it started leaking again. This time around I took the pump out myself and took it in to sort the leak out and upon putting it back in started leaking while cranking the engine and so I took out the pump and sent it back in again. Upon getting it back put it back in and had a go at starting it and when the car started it has low idle and won't respond to any throttle action. Apologies for the mouth full but what's my problem.....apart from me causing it lol
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
I'm sorry for the incomplete thread the site kept returning back to page while trying to post I hope the repost gives full picture
- Posts
- 18,999
- Location
- Buckinghamshire, UK. ('95 DT)
Well, we're up to 2 pages of wandering off topic, dicking about ans p!sstaking before we've even got the question out. That's about average.
So, top of pump hasn't been touched? Ignore my earlier answer. @wammers is the diesel God, hopefully he'll put in an appearance.
I am guessing you haven't got new chains on the car? What lift did you set the static timing to?
- Posts
- 12,223
- Location
- Sud ouest France !
Hey hey, the wanderer returns, welcome.
It sounds like the top of the pump isn't refitted properly as you said grrrrrr. If it's been opened to do seals, I bet they've not checked the pin in the hole.
It sounds like the top of the pump isn't refitted properly as you said grrrrrr. If it's been opened to do seals, I bet they've not checked the pin in the hole.
brianp38dse
Well-Known Member
- Posts
- 19,651
- Location
- heathrow
Was the pump put back in using an adapter and dial gauge to get the static point of injection correct they cant be just refitted any old how.
Datatek
Well-Known Member
- Posts
- 44,119
- Location
- Near Poitiers SW France
As others have said, the top of the pump may be incorrectly located, also if the FIP has been removed completely are you sure the static timing is correct?
- Posts
- 58,170
- Location
- Preston Lancs.
Where exactly was the pump leaking from?
Last edited:
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
Okay and I the case of this happening....what would be the next move?
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
The pump was leaking from one of screws on the top of the pump and then the second mating face from the top of the pump. Then it presented a leak on the head of the pump....I know, you must be thinking that's a lot of leaks right. Now there are no more leaks, just the idle and rev problem
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
I suspect I may have compromised that. So what would you suggest as a plausible solution?
Datatek
Well-Known Member
- Posts
- 44,119
- Location
- Near Poitiers SW France
Compromised what? If the static timing, you need the special tools to set it up. Have a look at the workshop manual RAVE for details.
Kelvin'D-MiC'
Member
- Posts
- 16
- Location
- Zimbabwe
My problem is I'm all the way in Africa, Zimbabwe to be more precise and don't know where to start to source that special tool....
Datatek
Well-Known Member
- Posts
- 44,119
- Location
- Near Poitiers SW France
Ebay is your friend, but really you need to put it on diagnostics.
