- Posts
- 1,108
- Location
- Worcestershire
I know the PTO on the back of the transfer box can be used to power various things, could it be used in reverse and if i bolted an electric motor onto it could that be used to propel the vehicle using batteries?
Hybrid 101?
- Thread starter yfo866
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hicap phill
Well-Known Member
- Posts
- 16,337
- Location
- Wiltshire
Probally… it’s only the same as engaging an overdrive
300bhp/ton
Well-Known Member
- Posts
- 5,029
- Location
- Near MK
To what end?
- Posts
- 6,225
- Location
- North Manchester
Can't imagine it being very efficient.
- Posts
- 33,936
- Location
- North Shropshire
I don't have anything to say here. Now if only it were in AG 
You need to find out what power the pto can handle, doubt it is much.
Wildefalcon
Well-Known Member
- Posts
- 1,685
Interesting idea. Presuming you're keeping the V8 and main box ?
Purely as a vapour build:
You'd need an overdrive type way of splitting the gear on main shaft that drives the intermediate shaft.
An old overdrive could be repurposed, with the syncro and layshaft ditched.
Tig a mounting plate to it, somehow, and an electric interlock.
Or, as an alternative, ditch the gear box, use an lt230, and power the electric motor from the 24V alternator. V8, electric motor, lt230.
Purely as a vapour build:
You'd need an overdrive type way of splitting the gear on main shaft that drives the intermediate shaft.
An old overdrive could be repurposed, with the syncro and layshaft ditched.
Tig a mounting plate to it, somehow, and an electric interlock.
Or, as an alternative, ditch the gear box, use an lt230, and power the electric motor from the 24V alternator. V8, electric motor, lt230.
- Posts
- 33,936
- Location
- North Shropshire
that wouldnt produce enough power? just connect v8 direct to lt320
- Posts
- 33,936
- Location
- North Shropshire
surely high power/torque going the 'wrong way' would just make things explode?
everything in the transmission is designed from the ground up to transmit power in one direction, ie from the engine to the prop-shafts/PTO? taper bearings, endfloat etc would all be upside down?
everything in the transmission is designed from the ground up to transmit power in one direction, ie from the engine to the prop-shafts/PTO? taper bearings, endfloat etc would all be upside down?
- Posts
- 33,936
- Location
- North Shropshire
assume that is output
Wildefalcon
Well-Known Member
- Posts
- 1,685
Over drive copes with full output of the V8.
Wildefalcon
Well-Known Member
- Posts
- 1,685
Range extender, plug in hybrid. 2.4kw alternator.
300bhp/ton
Well-Known Member
- Posts
- 5,029
- Location
- Near MK
Does it say 'B' hp? As in Brake. On a tractor the PTO is often rated in Shp (Shaft), which is something different to Bhp. I'm not sure how you could regulate power 'to' the PTO in any sort of accurate or even blinding guessing sense.
- Posts
- 6,225
- Location
- North Manchester
The PTO would need to drive a alternator/generator to charge the batteries to run the motor.
No expert but presume it would need a speed controller also.
No expert but presume it would need a speed controller also.
- Posts
- 33,936
- Location
- North Shropshire
i thought the discussion was using the PTO as an input rather than an output?
I would guess it means it could drive something that takes between 20 and 25 hp to drive it maximum
If I remember correctly some of the land rovers you could get governors for them
- Posts
- 6,225
- Location
- North Manchester
Ah my bad. I read it as using the PTO to drive a motor to propel the vehicle.
- Posts
- 6,225
- Location
- North Manchester
Presumably the drive train is disengaged when the PTO is selected?
- Posts
- 33,936
- Location
- North Shropshire
Transfer box in neutral
