Fairey 525/Superwinch H14 PTO Spares

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
D

D.G.F.S.

Active Member
Posts
421
Location
Cheshire
Hi All,

Does anyone know of any current part numbers for the universal joints for the above winches. One of my uj's are bolloxed (yokes worn) and in need of replacing but I cannot find any relevant part numbers. Apart from the ones in the manual. I spoke to the Superwinch technical support guy who quoted me £156 for ONE uj. Fook that.
Any help folks would be greatly appreciated.
 
think a mate of mine said he used ford transit steering linkage uj's (with a slight mod ;)
although if its anything like how much they charge for a door mirror be cheaper to go to fairy :mad: well over £100 our sprinter it cost about £45 :rolleyes:
 
My arse fell through with the quote I was given. I'm going to the local motor factors tomorrow, they said they will try and measure up one to match mine. Would a steering uj be strong enough for a winch? I was a bit unsure weather it would stand up to the stresses of a winch.
 
Will do. Was that part number for the yokes too because that's the bit I'm after? I can get most if not all the parts from Superwinch, the downside on that is I would need to sell the landy to fund it. The part numbers from Superwinch must be for their reference only.
 
D.G.F.S. said:
Will do. Was that part number for the yokes too because that's the bit I'm after? I can get most if not all the parts from Superwinch, the downside on that is I would need to sell the landy to fund it. The part numbers from Superwinch must be for their reference only.
Click to expand...

That's the part number for the u/j. If you go to a garden machinery or tractor place they should be able to locate the yokes to match that u/j once they know the u/j part number
 
I know its an American site but it may be of some use. Particually for you Ratty, they do a hexagon yoke as you wanted. Might be of use, might not. Best I've found so far. Hens teeth and the like...
 
D.G.F.S. said:
I know its an American site but it may be of some use. Particually for you Ratty, they do a hexagon yoke as you wanted. Might be of use, might not. Best I've found so far. Hens teeth and the like...
Click to expand...

There is a prop specialist on feeder road in Bristol called chards. They can get most parts and at a reasonable price if you want to give them a try. Nigel is usually the best one to speak to.
 
Cheers for that Ratty. I have found a local company who can supply a solid yoke of the correct size for under £30. A engineering firm has quoted me £25 to bore it out and fit a keyway.
With regards to your hexagon shaft and yoke Ratty, have you thought about getting a normal round yoke with a keyway and machining the end of a hex bar to 19mm dia with a keyway to fit the yoke? I've tried to find a hex yoke in the uk but not had much luck.
 
D.G.F.S. said:
Cheers for that Ratty. I have found a local company who can supply a solid yoke of the correct size for under £30. A engineering firm has quoted me £25 to bore it out and fit a keyway.
With regards to your hexagon shaft and yoke Ratty, have you thought about getting a normal round yoke with a keyway and machining the end of a hex bar to 19mm dia with a keyway to fit the yoke? I've tried to find a hex yoke in the uk but not had much luck.
Click to expand...

On a 110 the props usually have a sliding joint which is hex bar on one end and a keyway on the other. I was figuring that if I could have hex at both ends it'd make it much cheaper and quicker to replace in the event of a failure.
 
ratty said:
On a 110 the props usually have a sliding joint which is hex bar on one end and a keyway on the other. I was figuring that if I could have hex at both ends it'd make it much cheaper and quicker to replace in the event of a failure.
Click to expand...

I have just had a look at the winch manual for yours and its pretty much the same as mine. I have just picked up two new solid yokes (£25.76+vat ea) from a company called GKN Driveline Services Ltd in Leek, Staffordshire. Really helpful people too. I spoke to them about your sliding joint (took mine as an example) and he said to re-manufacture one a ball park figure was around £100. Give them a call (ask for Andy, he's the person who I spoke to about it)
They manufacture all types of props, cv joints, hydraulic rams etc.
GKN Driveline Services Ltd
Higher Woodcroft, Leek,
Staffs.
01538 384278

There is another depot at Sutton Coldfield West Midlands too. 0121 313 1661.
 
You must log in or register to reply here.

Similar threads

S
Fairey drum winch drive shaft parts
Replies
2
Views
3K
ronsealdeath
ronsealdeath
D
Pto Winch Spares
Replies
10
Views
1K
D.G.F.S.
D
JoeBodge
Fairey 525 PTO Winch
Replies
1
Views
3K
lynall
L
ratty
Pto shaft
Replies
3
Views
690
90truckcab
90truckcab
Booger
Morocco 2010 - Booger's Report
2
Replies
34
Views
11K
onelife
O
Back
Top