BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
unless its mine
How's it going anyway?
Will TUFFTEE be ready for next months shindig?
After some advice again!
- Thread starter sturose
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
How's it going anyway?
Will TUFFTEE be ready for next months shindig?
- Posts
- 83,310
- Location
- Embasinga stocæ
erm................
i am working on it
i am working on it
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
erm................
i am working on it
OH!!
Goin abit slow then?
Booked your seats with Ratty or Dorset, just in case??
- Posts
- 83,310
- Location
- Embasinga stocæ
erm................. i mite have
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
erm................. i mite have
FOOKIN ELL!!!!
HOW LONG??????
The rest will have rusted away by the time you finish
- Posts
- 83,310
- Location
- Embasinga stocæ
nah - it will all be new.
.
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
nah - it will all be new
New what??
New rust holes I bet
Then again, you had a shock at just how much rust there was didn't you?
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
erm................
i am working on it
FFS daft I can see I'm gonna have to pop down for a spot of welding between chats at this rate!!!
- Posts
- 83,310
- Location
- Embasinga stocæ
welding is the easy bit - its all the fabrication of parts and drawing them all up that more difficult.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
I int too bad at the old sheet metalwork??? Make cardboard templates first ya can't go wrong..
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
- Posts
- 83,310
- Location
- Embasinga stocæ
i got the originals in most cases.
if i remember - there was an invitation made a couple of times, Pikey, if yu were coming down.
if i remember - there was an invitation made a couple of times, Pikey, if yu were coming down.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Quote:
Originally Posted by The Mad Hat Man
welding is the easy bit - its all the fabrication of bull**** and making excuses that's more difficult.
Hmmmm.......
HAHAHAHAHAHAHAHAHAHAHA Fooking classic...
- Posts
- 83,310
- Location
- Embasinga stocæ
Hmmmm.......
lol - wait till its yo turn - i mean - how long duz it take to change a diff
.
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
lol - wait till its yo turn - i mean - how long duz it take to change a diff
Dorsets back axle went back on in no time last Saturday.
It's his engine wots comin out tomorrow
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
i got the originals in most cases.
if i remember - there was an invitation made a couple of times, Pikey, if yu were coming down.
I was a bit busy at the time, and transportless. the 90 should be ready by the end of next week & I feel the need to get the fook outta Hull for a few days. I'll see what I can do..
- Posts
- 83,310
- Location
- Embasinga stocæ
its a hull of a trip, but yu is always welcome.
BOOMER
Bloke from Dorset
- Posts
- 6,051
- Location
- All Over Dorset and beyond.
- Posts
- 83,310
- Location
- Embasinga stocæ
wud it be impolite to say i wannit done proper .
.
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
Have driven the 110 from Torquay to Hull in 1 run before. & it was packed to the rafters with Tools and ****e.. Even had two sets of ladders on the roof rack..
Similar threads
