Essex lanes

[666 george]

Exactly where i went mate

Old one was proper dead, rear bearing had collapsed and taken out the rotor so it was a paperweight. Got a refurbed one for £100 So now i am back up and running and with all this rain just in time lol.

Bl**dy hell they must have seen you coming (not unless it was 100amp)
I payed £65 for a 65 amp about 4 weeks ago,

 

[matthew2riches]

Geoff - what was that place you suggested once? Start-a-nator or someone?

 

[Brian S]

Startornator in Tiptree. Richard is semi retired but still fixes them for an average of around £50

 

[beerdude]

You can get repair kits and do the job yourself if you have the time/enthusiasm/knowhow but you don't get a warranty

 

[beerdude]

Oops just noticed the bit about the rotor, you don't get that in the kit

 

[Tuskenraider]

Yer its a 100amp one

 

[Co-Pang-Yang]

Need to get me a couple of them.

 

[Brian S]

I am sure I brought a new 100amp for about £120

 

[Tuskenraider]

Island 4x4 have the Denso ones for around £140 but a decent refurbed one will be just as good. Better than the chinese £50 ones on ebay

 

[Co-Pang-Yang]

Well could be a few changes afoot for the mighty Disco over the next couple of months.
New suspension, locking diff, Manual gearbox swap, winch.......

Only problem I can see is a also want a fast car and a house :lol:

 

[Drizz]

Well could be a few changes afoot for the mighty Disco over the next couple of months.
New suspension, locking diff, Manual gearbox swap, winch.......

Only problem I can see is a also want a fast car and a house :lol:

Dont forget to sort me a list so i can get the bits you want ready......

 

[Tuskenraider]

Well could be a few changes afoot for the mighty Disco over the next couple of months.
New suspension, locking diff, Manual gearbox swap, winch.......

Only problem I can see is a also want a fast car and a house :lol:

Dont forget round wheels

 

[Co-Pang-Yang]

Dont forget to sort me a list so i can get the bits you want ready......

Yes mate, going to conferm the parts list this weekend.

When are you back/thinking a out stripping it?

Dont forget round wheels

:lol: :lol: yer them too, mine got picked up yesterday so have to see what happens with that

 

[Drizz]

Yes mate, going to conferm the parts list this weekend.

When are you back/thinking a out stripping it

I'm back Sunday so I'd imagine I'll start on my next day off!

 

[Co-Pang-Yang]

Righto, I'm planning on gettin Mike to help me do the conversion so we can get it done in a day along with a couple of other bits.
Would your ramp be available if we decided it will make the job easier?

 

[Drizz]

All depends when

 

[wickford90]

Decided its time to move, so I am looking for a barn/workshop around Basildon Wickford Billericay area. not after anything posh just somewhere to store and work on the motors anyone fancy sharing a place or know of any? Also got 3 lots of heavy duty pallet racking that makes excellent huge workbench/storage. I use one and Matt has one in his workshop.Dan/Mikey/Chris any good to you?

 

[Drizz]

Thanks Geoff but I'm looking to move out of my workshop or at least sublet it as I'm loosing enthusiasm for the workshop. Wanna get mine done as far as possible then take it home and finish it there.

 

[wickford90]

Thanks Geoff but I'm looking to move out of my workshop or at least sublet it as I'm loosing enthusiasm for the workshop. Wanna get mine done as far as possible then take it home and finish it there.

Ok mate.

 

[Drizz]

But if its the orange and grey stuff, it goes for a fortune on ebay!