Search results

Hi, OK I'm probably being lazy but I don't want to strip the dash out just to check what flasher i have, so I'm asking LOL I'm swapping my lights over to LED and I know I need to change the flasher unit, can anyone tell me what I need to get as far a s how many pins and what one to get...

Hi, Has anyone got either a Clansman antenna wing box or just the door they no longer need? Thanks in advance Andy

And now I find the wanted section :-( Hi, I’m looking to militarise a ser3 LWB landy. Shes already Green and I have found a new old stock military soft top, hood sticks will be collected this weekend..... But I still need a couple pf bits, can anyone help with the following... Military bumper...

Hi, I’m looking to militarise a ser3 LWB landy. Shes already Green and I have found a new old stock military soft top, hood sticks will be collected this weekend..... But I still need a couple pf bits, can anyone help with the following... Military bumper (with bumperets) Rear Tail gate any...

Hi, Anyone know where replacement sanky trailer springs can be acquired from? Thanks Andy

Hi, Looking for a good 2nd hand 109 military canvas and hoop set, has anyone got one? Thanks Andy

Hi, Just a quick question... the power connector on the back of my ser 3 petrol starter motor is very loos and hence not making a good enough connection. Can I get to it and tighten it or do i need to order another one? Thanks Andy

Hi, I need to swap my front diff on a swb ser3 landy, my question is how far do i have to pull the half shafts out to clear the diff? Do I have to strip the hubs down or can I just unbolt the drive flange and get enough movement there? I will be changing the swivels and I have ordered new UJ’s...

I already have 2 ser 3 landys and a car but it’s getting long in the tooth now so I’m looking at my options. Its replacement would need to be up for taking 4 people towing a smallish trailer tent or caravan from kent to Scotland is reasonable comfort (maybe once a year). Budget is low as it...

Evening All. I seam to have a need to go digging into my front axle to locate and fix what I think could be a very dry bearing... so while I'm in there it may be a good time to fit something to improve top speed (or better still reduce the engine revs) Just trying to gauge what may options are...

As always your help and advice is needed once again… This is my 1 petrol landy in over 20 years and my 1st engine change.. And what a learning curve it’s been :-) So the engine a Ex Army 5 bearing 2.25 petrol seems to be a good one. When everything is running it’s great. I have fitted new...

Hi All, Yep Me again J You may of noticed I have swapped an engine in my early ser 3 SWB… We once again many thanks to all that helped with getting her running, greatly appreciated. I noticed I have a bit of a weep / leak from the oil pressure sensor on top of the oil filter. I don’t know how...

Hi, Well my engine swap is progressing and last thing today i spun it over to get some fresh oil moving around. My question is how do i go about setting the timing from scratch? There is no inspection flap to check the timing marks of the flywheel, just a locating pin (is this TDC?) I have...

Evening All, Quick Question.... before replacing the engine I have wire brushed the chassis in the engine bay and given it a good coating of red oxide I would like to know what is the best top coat.... I have looked at past post's and can see lots of comments, but no-one has mentioned spray on...

Evening All ! ok I'm about to swap out a old tired 3 bearing 2.25 petrol for a ex military 5 bearing one. Question 1: I'm reusing the ancillary's from the engine including the starter motor... so should I use the old flywheel from the 3 bearing engine or the one that came with the replacement...

Hi, OK I have started pulling the engine down and I have decided I want to repaint it the eggshell blue before putting it into the swb. So... anyone know where I can get the paint, will it have to be heat resistant and should I use a undercoat??? Many thanks in advance Andy

Simple question (I hope) I'm about to do some work on a ex military 2.25 petrol engine before swapping it. I'd like to fix it to an engine stand via 4 bolts that I understand are the same holes that hole the flywheel cover to the block..... Anyone know what size bolts i need as i would think...

Evening All... I'm hoping this will work, Ive recorded the annoying rattle that's coming out of my ser 3 petrol engine... If any one can identify what's causing it (latest suggestion is the cam shaft / followers etc) It would be great! its been like this for the last 8 plus years and the...

I'm having a few issues with my landy and I'm thinking a 200 300 Tdi engine swap may be the ultimate solution (ie a landy that will pull a full trailer up hill without dropping down to 2nd lol) not looking for break neck speeds, just to be able to tow at 60 and still talk to the person next to...

Can anyone recommend a breakers yard where i could get a replacement ser 3 petrol engine? I'm looking for a good runner to replace the current 2.25 lump in the 1972 swb. I live in Kent and all the old breakers yards they use to have land rovers are all gone now.... Any help gratefully...