Search results

BatteryMegaStore.co.uk Worth a look. 3yr warranty + free next day delivery. Ive had a few leisure and a batt for my p38 (1000 ca). Never had any probs. Hope this helps

One or two of your front brake caliper pistons may be sticking, I had similar problem, found a bit of rust on one of the pistons, changed them, straight as a die.

Hi I have some diagrams somewhere on valve block rebuild, i'll dig them out later. The p38 spares link is good for block bits. There is some free software authored by Range Rover God 'Storey Wilson' in the States for EAS unlocking, resetting & calibration. If you go that way, then either...

Hi Partco (Brown Brothers) sell batteries which come with a 3yr G-tee. Around £60 if my mem serves me well

Hi You're ODB II diagnostic socket is is the passenger (near side) footwell, just behind the foot heater vent. Hope this helps

Hi Yes, it's ATF. Just check the oil in the trans. is reddish in colour b4 you go splashing out

Hi It would help if you stated what vehicle and gearbox you have. Classic, P38, Manual, Auto, Borg Warner? Classic Range Rovers: Early boxes with a limited slip differential:- Gearbox - Hypoid gear oil, viscosity SAE 80EP to API GL4 Transfer box - Hypoid gear oil, viscosity SAE 90EP to...

Hi K seal in my opinion is brilliant, and for £9.40 + Del. if it doesnt fix your rad. it will certainly fix any leaking 'o'rings you might get in the future. Fixed mine. Presuming the rad leak is not major, i'm sure k seal will do the job, heres the link: Kalimex - Advanced repair, DIY and...

Hi Before I get you into the wiring loom, check that your filler cap will unlock, and get a hair dryer and blow dry the tailgate button for a good while, probably ingressed with water from car wash. I was under the impression range rovers were meant to be washed by hand. Let us know soon if...

Hi Advisable not to poke too hard with the coat hangers as the tubes are made of rubber, and if you haven't got a hole in them, a coat hanger can soon give you one. Wet carpet on drivers side, my guess is that it is the heater 'o' rings. You didn't say where you looked for loss of coolant. If...

Hi P0134 - 02 sensor circuit no activity detected (bank 1 sensor 1) This code refers to the front oxygen sensor on Bank 1. Basically the oxygen sensor is inactive. Here's why: The powertrain control module (PCM) provides a baseline voltage of about 450 mV on the oxygen sensor signal...

ELECTRONIC TRACTION CONTROL The purpose of electronic traction control is to aid traction when one wheel on an axle spins whilst the other still has good grip, e.g, if one side of the vehicle is on ice and the other is on tarmac. The system works by applying the brake to a spinning wheel in...

Hi Following battery removal, rad/cass sec. code will need re-entering. Windows and sunroof will need to be set. data in trip comp. lost. key fobs will need synchronising. To synchronise: If the vehicle is locked, press the 'unlock' button on the handset and unlock the vehicle using the key...

Hi Fuse box in engine bay, behind battery, fuse 30 & 32. Both 30Amp Fuse box in side of right hand seat. open drivers door and u will see a little flap in your seat trim. fuse 2 - 30A. If this on goes your display will tell you. I think the relays are in yhe becm if not in the engine fuse box...

Hi Do you able to uncompress or open a zipped file? If so, I could send you the whole range rover manual including the most important ETM - electronic troubleshooting manual. (Also includes Discovery II, Freelander, Defender). Unzipped, the lot stands around 649Mb. Only managed to squeeze it...

Hi I've been reading some old threads, and there seems to be similar issues regarding (Malafax Dand) Storey Wilsons' EAS software, unable to sync, etc. Storey Wilson has put a considerable amount of time and dollars into this software which some of us use for free. So at the very least one can...

Hi Have you checked the universal joints on the props? Make sure handbrake is OFF before checking

Hi Your OBD - DB9(serial) lead, if you did not make this lead up yourself, then please check the corresponding pins conform to correct continuity. Hold the plugs in hand & look at the shape as shown. Put a continuity tester on each corresponding pin. Let me know if you have these values, or what...

Hi, I've just joined. I have used EAS with no prob. What was stressed to me was the importance of the cable. I made my own cable (OBD - USB). No converters. I just cut off the DB9 and wired direct to the OBD. The converter may be routing the wires incorrectly. Might be worth the price of a lead...