Search results

Hell on my 2004 td5 I have no rear fog lights but the switch works and the Tel tail led comes on but no power to the bulb holders in the rear bumper . As this is a bcu system can anyone tell me where to go next please ? I'm a bit lost .

Hello , I like to add a additional coolant temperature guage and sensor with the warm weather and doing quite a bit of Laning up hills and the like . My question is where is a good place to put the fitting tube for the sensor ? In the top hose before the head connection ? Thanks in advance

On my 2004 td5 I have lost dipped headlamps but working sidelights and main beam and flash. With the ignition on a lights switched on there is no power at either of the fuses under the steering column . studying the schematic I see in the engine fuses box , fuseable link 10 feeds the stalk...

On my 2004 15p discovery 2 I'm replacing the FPR but which gasket is correct ? I have looked on the internet and I am being told that MSX100080 which has a square hole in and is for a 15p then other places say a MSX100010 is for a 15p and had a round hole in the gasket. can anyone confirm...

I bought from Gwyn Lewis a kit to change breathers as my front one is leaking badly around the pipe, the plastic insert must be worn . Apparently pull out insert and tap out the hole ... one issue the tap will not even start in the bushing in the axle case and can not drill out in place etc as...

How do I check the fuel pressure on my 15p td5 ? I took the temperature sensor out and fitted adapters to 6mm tube and to a guage , starts and runs but no reading on the guage . Tried another guage and the same, when blow air with an airline it moves up past 4 bar no issues . what am I doing...

My 2004 td5 with 130k miles had suddenly developed a problem . It is down on power when engine is under load and missfiring and it a real pig to start and even after priming sequence still not easy to start . It all suddenly started yesterday and was driven local to me down a duel caridgeway...

Hello all , my clutch is feeling it's getting on in life . Pedal getting high and juddering when pulling away but no slipping . But also the DMF is clunking a bit more as letting clutch off . So time to change the clutch soon, I have ordered a powerspec kit from LOF . I replaced the slave 9...

Hello all , I am currently using 245 75 r16 on my d2 , but going to change to modular steel wheels 2 questions really 7 or 8" wide and et25 or et35 ? I can not find a explanation how they are measured or sized compared to the standard wheels . Thank you.

Hello all , just took the shuttle valve plate off and a bit dirty in there bit no moisture or corrosion . So going to go with the mod . I see 2 ways doing it . One way splice into the 2 pin connector in parallel and leave the connector in situ. The other you snip the connector and remove...

Hello , I'm currently remove my sls and going to coils on the rear , airbags both gone , height sensors gone and so has the compressor . I done the conversion and getting the suspension changed to rear spring in the bcu etc next week . But where is the fuse I need to pull looked in my...

I will be building a box unit in rear and have no rear seats in or belts how do I legally convert this to a 5 seater ? Insurance as a 5 seater yes but what about dvla ?

I know this may been covered before buy mine have been randomly coming up and then turn off cone back in a hour and there gone then may not happen for a week or 3 weeks . So scanned it on our work diagnostic tool ( texa ) and came up with a stored fault which not currently active . Its said "...

Hello all I have just got hold of a box from a 2000 disco 2 with a diff lock mine is a 2004 without a difflock. I'm pondering do I swap the complete transfer box or do I swap the diff lock assembly onto mine ? It's pretty dirty so if do replace whole transfer box I will replace the seal ...

My Watts link is knocking is getting worse and was thinking to replace but 2 friends replaced there's to last less than a year to go again . I heard on rear phanard rod conversion , which is best route to go down ? Daily driver with some off roading at weekends .

Both my lower ball joint haters have split and noticed when was jacked up checked other joints that they started to creak slightly . So looks luke 4 x new ball joints . My question is I have seen the ball joint g clamp style tool but from what heard the do bend and I hear the LR joints are is...

Hello all , I'm wanting to remove my roof rails due to one is leaking and I'm going to make a custom roof rack so lower the better if rails are off . My question is there any special blanking plugs / grommets for the holes in the roof or are they a special shape? Mine is a 2004 facelift ...

My diff pinion seal leak is getting worse , I ordered a seal and attempted to tackle it but I'm stuck trying to get the pin that is in the flange before the bolt . Come across 2 problems 1 , whist in air the whole diff turns when trying to remove the pin with socket and bolt technique and 2 ...

I'm in need soon for a power steering pump, its leaking fron the front seal and leaving small puddles . I have looked for a few cheapest is sh**part or a OEM is a bit more but when looked into manufacture tes say OEM but supplied by britpart ?? Only other supplier I found is bearmach. What...

I'm in the need for a new nearside rear check strap . When operating the door makes a awfull clunk sound . Where can I get these from without paying rediclous money for them ? Also my rear door is clicking the same on the strap. Where the arm mounts onto the body I see the bush / pin has worn...