Search results

I'm cracking on with a galvy chassis and bulkhead swap, I've hit a snag and am proper struggling for a solution. Basically - steering column is now too long... Summary: 1) Rear tub right against back bumper tabs as far back as it can go and sits nicely in place. 2) Bulkhead spaced with one...

Anyone know where I can get hold of these tyres ?? Thanks all. :)

Anyone got a single simex extreme trekker 35 x 10.5 x 16 for sale ? ta !

Hi all. Had to cut the bolts from my old arms front and rear as they were siezed solid (fitting new QT arms... ) so need new bolts. Are these specific tensile or will local hardware store type bolts be ok ? ( so long as they're correct fit in the bushes, no slop etc) Also, on the chassis...

Hi all, Changing springs on a 90 Truck cab 300tdi with roll cage, wing kit and 8274 twin motor on front. All castor corrected QT arms and wide angle props etc. Procomp ES9000 + 4 shocks all round. have got the following on at the mo........ BA2101 255 lbs 40mm lift front BA2102 295lbs...

2003 V6, never missed a beat but now got s prob. Basically it started with a misfire and engine light intermittently comming on. Got a diagnostic check done, code was a misfire on cylinder no 3. Changed plug and coil pack but still running lumpy and tickover 'hunts' very slightly. Engine...

Happy new year everyone. Got a problem with a 300tdi. Been running fine. went to boxhead over christmas, every so often lost power and cut out, especially on slopes. Starts up straight away again though ( with a little more cranking than usual) . Fair enought I thought, low on fuel. (guage...

Hi all... Can anyone make anything out of a problem I've got.. Basically an Intermitent starter motor..(defender 300tdi) Exciter wire (signal wire) has a constant 10.3 volts on the multi metre when ignition key is against the spring. Terminals all good etc . Sometimes it starts sometimes...

anyone know where I can get a35 x 10.5 x 16 nr side Simex ET ? bad puncture at the weekend and no one seems to have any !! Cheers.

Eh up. anyone know where I can get me mits on a roof and rear panel to convert my 90 hard top to a truck cab ?(epsom green) Been looking for a while and they seem as rare as rocking horse #*$!

Hi Guys, Took landy out today, (90 defender 200 with 300 tdi engine) everything fine. Got in this evening just to reverse it to park it for the night. Started on the button, switched lights and spots on as was peeing down, reversed slowley, engine and everything else has just died. No side...

eh up all, two axle probs I could do with some advice about please :D broke front half shaft today, striped everything down, inside the axle casting is MINGING !! silt mixed with diff oil mixed with god knows what ! is it acceptable to jet wash inside axle ? (obviously letting it dry etc)...

hi all... bit of a prob I could really use some help with. . . Freelander v6 petrol 2003...54k miles. Short run and car was fine, got home, left it for few hours, went to go out again and wouldn't start....checked spark and injector signals and all ok. so I think i've eliminated crank sensor...

Mornin all... Wanna put a disco axle onto my defender 90 (to change to 24 spline and change to disk brakes) Please could anyone tell me if my 4 bolt flange off my old axle will go straight onto the disco axle ( currently 3 bolt with the disco rubber cush doobry thingy) I read somewhere...

Mornin all... Read loads of threads on this but nothing really answers me question. Temp gauge was working fine...changed a bulb in fuel gauge, put dash back together now temp gauge goes almost all the way up (into the red) even when engine is coldish. D'oh ! (_8(I) Been over and over...

Evenin all... Done swapsies (ie not cost me anything.....yet !!) and got a ARB 10 spline locker (new) to go on rear axle. I'm currently running 10 spline shafts on my 90... was really after opinions if it was worth fitting or better to go for a 24 spline locker (can swap for the 1- spline...

eh up chaps... Silly question I know but I can't work it out. What rear diff have I got if it looks pretty standard on the prop shaft side but the rear of the diff housing seems alot bigger than the pics an the haynes manual and compared to disco axle etc. instead of the pan shape its more...

Hi, Trying to get me noggin around this one. getting conflicting answers. Fitted a winch to my 90, do I go for a second deep cycle style battery and decent split charger or Two batteries (same) and just double the amp hours but keeps it simple ? Not intending to do winch competitions etc just...

Eh up chaps, Picked up a Mantec Jobble suitable for a 300Tdi very cheap from a mate but it don't fit..I've got a 200 with a 300 engine. The vent in the wing is completely wrong shape etc. Is there summit that will fir or do i cut the wing ? Any help please cause i'm bit stuck ! Thanks.

Hi. how many seals should there be on the front doors of a 90 (1992) Reason I ask is just picked up my landy with doors not closing very well. There is the normal door frame 'squashable' rubber seal as you'd expect around the door frame but there is also another seal 'glued' around the inside...