Search results

Thanks for the advice.

Hi All, I need a new front downpipe for the landy. There are lots of standard parts for £30 - 50 is there a performance part that will fit to the exisiting middle and back box. They are too good to replace the whole system so my thought was buy a better one for the front then replace as I go...

Yes I agree however there is a recess where the o ring fits. However I took it to a local fitters shop and lots of heat and two foot stilsons won the day. I need to clean all the rust off now then it can go back together. I can see why it rusts it gets the brunt of all the water.

Thanks Guys, Hifly, thats what I have done but it just wont budge. The only thing left is oxy heat it rather than blow torch. I am not worried about the o ring I have lots in the garage. Here is a pic. [/URL][/IMG]

Hi All I have a problem where the oil cooler pipe wont come free from the male/male adapter. Yep tried everything I can think of. Does anyone have a part No for this so I can get a new one. Its NOT ESR 1253 as it seals against an o ring on both sides.

I am guessing it goes to the susspension capacitor but what should it do? Its a green-bluish colour.

Thanks guys I have just gone to the alternator side as I think its the 100A pulling the load 0.73A and I came across this loose wire any Idea where it should go or do? http://i192.photobucket.com/albums/z2/coldcomfortfarm/alternator.jpg

Hi All I have a parasitic load which I cant seem to find. I can trace it to the big fuse board under the engine bay. Does anyone have a wiring diagramme of what each of the 100A / 60A / 45A fuses feed. I guess sub fuse boards. I was half way through looking for it when I dropped the lead and...

I have a similar problem, my battery has to be in tip top shape to turn it over when cold. I use a battery isolator switch at the moment until i find the problem. I am getting about 1ah draw on the battery. My Telehandler had the same problem and woudl always start when jump started. I...

OK I am back, The pump timing was out very slightly however when I go back to it now its like the battery is dead but its not so I am now assuming the starter is on its last legs. My telehandler had exactly the same fault , i replaced the starter and its never missed a start since. I have two...

Can you transfer any heat to locally melt the plastic so it grabs again? induction heating would work. i.e heat the metal not the plastic.

I agree with sidways. I cant hear a thing from my autpo box but I do have problems with air in the system and the sloshing in the heater matrix.

Could you drop some glue down the gap to stop it spinning? Do you mean the brass insert into the plastic snorkel. A pic would be good.

Brill TY.

Brill thanks Brett I have spent ages googling but could not find a dedicated company who do the parts. I will photograph it and send it them. The thought crossed my mind if the rust worm has eaten this I guess its spread. I have some AC150 which stops rust so I may give that a spray and...

Hi All I have just noticed a small rusty hole just above the passenger cill rear door post. Is this an easy weld fix or would you guess the cills will need replacing too. Its just gone through an MOT with no advisory so I guess it got missed or its not an MOT point. As for the door post...

Difflock now works. Well I took the knob off the top and the outer gator and slid a thick walled pipe over the shaft. I pulled it towards the passenger side whilst smacking it hard with a lump hammer from the drivers side. It moved and went into difflock. Did the reverse then back again and...

give it a charge overnight and then take it to a garage or Halfords and they will drop a tester on it to see if the battery dies. I had a battery that would fail every now and then and all it needed was a good quality battery charger on it from time to time to condition the battery. I do it...

Any News?? Snows coming you know:)