Search results

Could anyone point me in the direction to purchase a new intake hose for my TD5 90? I've found mine has a rather large hole in it! I've got a raised intake so not sure if it's original or not. It's the flexi hose/duct/pipe that connects the airbox to the plastic union which I think has a drain...

I'm looking to replace the props on my 90 TD5 for some wide angle jobbies, Gwyn Lewis was my first port of call but I stumbled on the terrafirma set which are a bit cheaper. Are they any good or should I just fork out for the Gwyn Lewis set?

Does anyone know where I can get a panhard rod fixed eye (the type that you can put normal bushes in) to replace the rose joint that's on mine? Stainless bushes are lasting about a week at current and I'm getting fed up, I think it's an extreme 4x4 rod (came with the vehicle) but they want over...

I ordered the following kit from island4x4 but the bearings don't fit the stub axles on my 1999 TD5 90 front axle? The bearings fit the hub fine but won't slide over the stub axle. Could someone with more knowledge point me at the right kit? 2 x Wheel Bearing Kit (OEM) 90/110 D1 RRC DA2381...

hi, does anyone know where I can get a replacement 8274 drum? Can't seem to find one apart from the fancy freespool ones that cost a fortune!

Has anybody got a clue as to why I've now snapped 2 front props on my td5 90? First one I was kinda asking for, loads of articulation and gunning it. Today my 2 day old double carden one decided to snap on the flat with barely any drive, I was just pulling away in reverse no big revs and bang...

Hi all, currently I've got an 8274 (standard) and D44 bumper on the front of my 90. It came with it attached and I've had one before but never really been that fond of them, fast with no load but lacking power under load, plus I'm just a casual green laner so it's a bit overkill. I've also got a...

so I've had my 1999 td5 90 for a few months and I've not stopped fixing it! Finally got close to having the perfect landy then she let me down in the worst way. Parallel parked in the middle of down and it wouldn't start, 3 hours until we leave for holiday. It has a factory immobiliser which...

I've got a 1999 TD5 90 and the rear shafts are miss matched, the offside (short) is a solid 1 piece but the nearside is a 2 piece. Does anybody know if they should be solid or 2 piece? I've asked a couple of buddies one with a 2001 90 (1 piece shafts) and one with a 2002 90 (2 piece shafts). I'm...

Ive got a carling contra ll mon off mon switch that I'm trying to wire to my warn 5 pin plug using the existing remote cable (I cut the controller off as it was a bit smashed to bits) I've wired up as instructed on the wiring leaflet for the switch but something has gone wrong somewhere and the...

So, think I've bought a lemon.... 1999 TD5 90. It's got a rattle when I lift off on over run but only below 35mph, it's pretty loud and a bit worrying, seems to be coming from the rear but sound travels so can't be 100%. It also happens when 1 wheel goes over a bump? It's present in every gear...

Hi folks. Thinking about getting myself a centre diff as I've been embarrassed a few times recently in my D2 although I am truly amazed at how well it copes with the traction control alone. Unfortunately mine is a 2004 so has not got the guts for the Ashcroft conversion. I'm looking to swap for...

Hi all, my 2004 td5 started rattling and squeaking on the way home from a laning trip yesterday. There was a little bit of wading involved which gave the engine a nice soaking in some brown water. On investigation it's coming from one of the 3 pulleys on the passenger side. I've got AC, PAS and...

Can anyone give me a step by step guide for how to save BCU setting changes? I've removed the air suspension on the back of my D2 and replaced with coils. I've left all the hardware in place and wired up although I would like to remove it all at a later date. Buddy's got a nanocom evo so we...

Lifted my D2 2" and since the anti roll bar links ended up getting cut off I fitted a new set. Should've seen it coming but they've both managed to dislocate for obvious reasons. What do folks do to cure this issue? Had a quick scan for extended links but nothing so far. I hear you could be in...

Just took the leap and removed my airbags. I've read lots of threads on the job and it only took about an hour an a half including fitting 2" lift and dislocation cones. No warning sounds/lights yet but I'll be deleting the air system later on. My question is what to do with the compressor now...

Can anyone point me in the direction of a supplier of decent steels for the D2? I can find modular wheels easy enough but fancy something different, otherwise I'll be fitting M/T's to my 18" alloys! I've always been a fan of the mach 5 type but can't find anything with a 120 PCD.

Hi all, does anyone know where I can get steel challenger (mach 5) wheels to fit a disco 2? PCD 5 x 120. Thanks.

Hi all, after 15 or so years of 4 defenders and 3 Disco's I'm back yet again! This time sporting a lovely 2004 Disco TD5 auto which I've instantly fallen in love with. The test drive was up to Snowdonia with the Mrs and dog for a camping trip, weather was ****e and we ended up legging it at 2am...