Search results

My clutch does not disengage the gearbox a 100 % so gear change can be difficult so far I have Bleed the clutch manually that is one person in the cab on the clutch pedal the other outside on the spanner, up down up down. No good can’t get 100% pedal. I have pressure bleed the system with...

1994 2.5 TDI Here’s one for you my clutch master cylinder is knackered, so got onto the net and bought what I was told the correct cylinder part no AEU 1714, it duly arrived and I removed my old cylinder and offered up the new one, but if I fit the new one I can’t get the top off to fill it...

Hello I wonder if anyone can confirm my thinking, when I use my indicators left or right the dash light doesn’t always flash, the outside indicators all work but the display light doesn’t always.

I ordered from the bay a slave cylinder for my 1994 200tdi discovery, it arrived today my question is what length should the cylinder be from the flat where you screw into to the front where the rubber bung goes over, I have measured and it appears to be just over 4” / 105cm

When I twist the output shaft that serves the front axle on the transfer box there is play, it moves side to side, put a little bit more pressure on the twist and it moves a little further, sort of stops then moves the extra bit if you understand what I mean, the coupling on the axle does the same.

Aframe ball joint removal, mine I think had been in there since new, there is bits and pieces of information on how to remove the joint but for me it all seems a bit sketchy , so this is how I got it out. Firstly I jacked the back axel up as high as I could get it and then put two heavy duty...

Probably covered before but I can’t find any imfo on my question, What is the best way to remove the two long bolts that hold the ball joint to the Aframe, mine appear to be sized as was the ball joint nut, now in bits

Mk1 discovery couple of weeks ago my dash indicator light stopped working but my indicators are working fine, so fiddled with the indicator stalk and here and there the dash indicator display light came on, but it will not stay on so changed the indicator stalk but the display light still will...

I fitted a Borg & Beck clutch New Slave Cylinder New Leaver and new Master Cylinder, so everything is new I removed the clutch damper and fitted the line straight to the slave, there are no leaks anywhere. Since fitting the clutch about 8 months ago I have continually tried to get a decent...

My Disco has done over 160,000 is there an oil anyone would recommend for an high mileage engine

My front prop shaft threw a uj bearing cup and the spider then gave the coupling a good beating before dropping out, the damaged coupling is the end that slides, my question is are both the front and rear prop shalf sliding couplings the same, in other words can I fit the slider coupling from...

My disco failed MOT today on a leak from the seal above the drop arm my question is can I change the seal without taking the box off

Can anyone tell what size hex I need for the gearbox filler screw on discovery 1

Bought my disco 1 clutch from Island 4x4 through the bay, it failed the next day and after searching the forums it appears Britpart do a large line in crap parts, anyway I wrote to island 4x4 explaining the clutch had failed miserably and I would be returning it for a full refund, what a...

How long does it take to bed a new clutch in, 200tdi

I pulled my engine out and changed the clutch, a helpful mate helped, after putting it all back together for some reason the alternator is not charging, but the alternator is working I checked it, so it's got to be down to wiring surely, I have a feed wire on the starter motor and a smaller...

I have a discovery 1994 200tdi, I have just replaced the clutch and lever, I fitted the slave cylinder through it's plate which also has another I am told a damper on it, I blead from the slave cylinder until all air had gone, but I still have no clutch, theres no leak from slave, any ideas what...

Hi chap, I have disc mk1 200tdi, I need to get engine out to repair clutch lever, how do I get at the bell houseing nuts.

My heater refuses to work on any setting, but drive along and suddenly it works, any ideas guys

can anyone tell what the clearances are on the tappets on 200 tdi