Search results

No I didn't pay for the rac warranty but I wouldn't be surprised if it was included in the price.

Well I have got the vehicle back they have replaced the master cylinder it is a bit smoother changing gear but the clutch pedal still disengages at the same low point near the floor but I am still sure it still needs improving, I questioned them on this they say the clutch dosent slip. I...

I have booked the car in for Monday at the dealers they think also that it is a clutch hydraulic problem slave cylinder or master cylinder even both. Just hope this fixes the problem,and its no charge.

Contacted the dealer they will have a look at it on Friday,its the clutch it only disengages gear when the clutch is pressed within half an inch of the floor and even then the gear lever has to be forcefully applied to get it into gear just hope they don't try and make out its fine.

I will contact the car dealer I see what you mean it should be the responsibility of the car dealer as the RAC warranty is for something going wrong after the purchase and not as it was when I bought it,thanks anyway.

Hi When I bought my freelander 2006 it came with 3 months gold warranty does anybody know how the payment works for any work done my local garage says when the work is done I have to pay the garage then get the RAC to refund the money back to me,mind you they aren't a approved RAC garage as they...

Hi Should the clutch pedal need to be pressed right to the floor to change gear the gear lever seems only to engage on the last inch of the pedal to the floor.As an update to this I am not sure now there is anything wrong as I have driven it more and more I seem to be engaging the gears a lot...

Hi exactly as you said flap dropped down pressing ok button good job you told me as I was convinced it wasn't fitted feel a bit daft now thankyou anyway.

Hi I have just bought a freelander 2006 2 litre HSE ,there is some cds for navigation and a radio with a cd button but no where to load a cd not having a manual is the cd player meant to be above the radio if so the former owner must have removed it.regards Martin

Hi I am considering buying a freelander 2 S four wheel drive but I am a bit dubious because it hasn't any terrain response,daft question this will it still perform in the snow as did my previous freelander 1.Regards Martin.

Hi Do all the Discovery 3 models have Terrain response installed.Regards Martin.

Hi I am thinking of buying a freelander 2 2007 0r 08 some of these i have seen advertised have had 80000 miles to 120000 miles on the clock now not knowing much about diesel engines would these engines still be good for another 100000 miles or less or should i steer clear of them.Regards Martin.

Hi When the freelander changed over to the BMW engine is it correct that these are chain driven timing belts and would they still have to be changed as the old timing belt.Regards Martin.

Hi If possible can you tell me when the BMW 2.0 litre diesel engine was first used for the Freelander 1 as i am considering buying a reg 04 or 05. regards martin.

Hi i know this might be a stupid question but what does the LN stand for applied to the freelander 1, i think my petrol 1.8 may be one of these.Regards Martin.

I agree I will buy a diesel hippo.

Hi Is it possible to replace a 1.8 petrol engine with a TD 4 engine.Regards Martin.

Hi The leak is just below where the exhaust is connected,like you say could be anywhere, i will find out next tuesday when it goes into the garage at work that is the garage built to service the factory delivery vans my mate jack who is retired uses it to do all the staffs cars as well cash in...

HI Its due to be examined for the leak next tuesday,anyway it might seem a bit daft but i have ordered an inlet manifold gasket a water pump and a timing belt.On the hoses i cannot see any leaks,so that leaves me with the header tank or the thermostat housing leaking.

Hi Its the dreaded 1.8 petrol,drain from the ac is that air conditioning it dosent have any, as for the leak i have now discovered it is on the front of the engine block i think where the inlet gasket is located,Regards Martin.