Steerin damper

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
I got deCarbon's on both 90 and Rangie. If you need to take it off and refit it's a tw@t, and the extra £7 for the Bilstein is worth it as you can remove and refit without damaging non-standard nuts that are fookin expensive to buy replacements for. I have a bag of nuts to fit deCarbon shockers/dampers that you can have for a small fee ;)
 
Aye a did jus gotta get time tae fit now and try it out, got the nuts soaked wi wd40 and wont get near it till sunday as im in glasgow till friday then a weddin on sat :-( just went for a stock one in the end, You get yer wheel bearings ?
 
landy10 said:
Aye a did jus gotta get time tae fit now and try it out, got the nuts soaked wi wd40 and wont get near it till sunday as im in glasgow till friday then a weddin on sat :-( just went for a stock one in the end, You get yer wheel bearings ?
Click to expand...
Time tae fit it!!!! It only takes about ten minutes, if that, tae do! just mind on that there's usually two nuts on the bottom (passengers side) of the damper;)
Aye, got me wheel bearin's and the inner seals... forgot aboot the other seals that are just a wee bit smaller!!!! That'll teach me tae get there at 5 tae 5:rolleyes: The bus is sittin' on axle stands at the mo', so's ah'll have tae get the mrs tae run me into town the morn!!:eek:
:D
 
Bit late (again) but we got ****part cellular on disco, super gaz on series, quite good. Nice ride, the series has monroe shocks on back. Need to do fronts. Disco has cellulars all round, nice ride, lets see how long they last!
 
bustersbus said:
Time tae fit it!!!! It only takes about ten minutes, if that, tae do! just mind on that there's usually two nuts on the bottom (passengers side) of the damper;)
Aye, got me wheel bearin's and the inner seals... forgot aboot the other seals that are just a wee bit smaller!!!! That'll teach me tae get there at 5 tae 5:rolleyes: The bus is sittin' on axle stands at the mo', so's ah'll have tae get the mrs tae run me into town the morn!!:eek:
:D
Click to expand...
Wish i hud ten minutes to massel, its matts burfday the morra anorl!
Im gonna tell yer doris what ye said bout her piccy taken and you'll be walkin! :D And its been ****in doon most of the day and i did go oot to start it earlier but the rain got heavy so i only got as far as puttin the wd40 on and the tools organised:mad:
 
a steering damper is not required to be a high performance damper , its usually stationary unlike suspension dampers that are constantly moving thus causing heat from friction thus needing to be tougher.
unless its made from cheese a standard damper will do exactly the same job as an expencive aftermaket jobby , dampen the feedback from the road going into the steering.
unless you drive at 150 miles an hour over a freshly ploughed field , then you might want to consider something stronger.
like ouzo.
 
landy10 said:
Wish i hud ten minutes to massel, its matts burfday the morra anorl!
Im gonna tell yer doris what ye said bout her piccy taken and you'll be walkin! :D And its been ****in doon most of the day and i did go oot to start it earlier but the rain got heavy so i only got as far as puttin the wd40 on and the tools organised:mad:
Click to expand...
Excuses- excuses! it's no rainin' now, and it wasnae rainin' when ah took the stuff off tae do me bearin's outside earlier:rolleyes: :D
The mrs has gone tae bed now, so's ah'm safe;) :D :D
 
You must log in or register to reply here.

Similar threads

C
Other Disco 1 V8 Auto gearbox
Replies
19
Views
2K
Cappo
C
S
Looking for another unreliable bun fun British car!
Replies
7
Views
681
Scmtb
S
R
Wheel and tyre advice please
Replies
10
Views
879
Repoman
R
N
Any Recommendations for Remanufactured TDV6 Supply & Fit ?
Replies
3
Views
2K
DanClarke
DanClarke
D
Crankshaft damper
Replies
12
Views
1K
freelanderoig
freelanderoig
Back
Top