removing window winder handle

Ham Salad · Jun 4, 2013

110 DEFENDER HARDTOP 300Tdi 1998
Any idea how to get the window winder handle off.
The book says you have to prise out the plastic insert and remove the screw,
but mine doesen't have an insert to remove, the handle is solid, i've tried prising it off but no joy, anyone got any ideas please.

the_wolf · Jun 4, 2013

Post a pic up so we can see. It should have a little bit of plastic you can prize off to gain access to the screw, its pretty much exactly the same as all other window wiper handles on any other car

johns90 · Jun 4, 2013

There might be a c shaped clip behind the main part of the winder. Holding it on the winder arm

ActionDan · Jun 4, 2013

It will have a circlip behind the winder - my 1998 defender has circlips rather than the removable insert.

To see the clip, you need to push on the door panel and the black circular bit between the handle and the winder - you should then be able to see the clip in the gap and get some long nosed pliars in to release it. It's a bit fiddly!

MrJC · Jun 4, 2013

Yes it will be a circlip, took me a while first time the fiddly little gits.... one tip... refit with the window closed tight and fit the winder at '10'oclock' for the drivers door and '2 o'clock' for the passenger side... then it wont be rubbing on knees.

postieparr · Jun 4, 2013

The circlip can be a pain to get off. I found sliding a bit of rag between the door card and winder and rotating it about meant it would catch the clip so you can pull it off. Watch out it can come flying off though

timtheenchanteruk · Jun 4, 2013

the circlip doesnt need to come all the way off, I manageg with an allen key, use the shorter end to nget under the loop of the clip, and pull to remove at the same time.

refitting is easy, shut the window, fit in positions as mentioned before, put the circlip back into position, and a sharp whack gets em on.

TimC · Jun 4, 2013

MrJC said:
Yes it will be a circlip, took me a while first time the fiddly little gits.... one tip... refit with the window closed tight and fit the winder at '10'oclock' for the drivers door and '2 o'clock' for the passenger side... then it wont be rubbing on knees.

Takes about 20 miles before your cursing it otherwise

timtheenchanteruk · Jun 5, 2013

TimC said:
Takes about 20 miles before your cursing it otherwise

that long, was 20 seconds for me, but i do have long legs

TimC · Jun 5, 2013

timtheenchanteruk said:
that long, was 20 seconds for me, but i do have long legs

I always knew they built defenders for people with no right arms but always assumed you were alowed a right leg.

Can always wind the window down to make room for both I guess

waldershelf · Jun 5, 2013

I use the hooky thing from a set like this Clarke CHT161 4-Piece Mini Pick & Hook Set - Machine Mart push the door panel in, locate the clip opposite the handle and give it a tug, once you've done it once it's easy.

Ham Salad · Jun 6, 2013

Thank you all for replies and ideas, wanted to move as someone said above to ten oclock, bloody winder pressing on the muscle in my leg gets a tad annoying after a while, done now, first a bit of a faff second a bit better..........

removing window winder handle

Ham Salad

Active Member

the_wolf

Well-Known Member

johns90

Active Member

ActionDan

New Member

MrJC

Well-Known Member

postieparr

Member

timtheenchanteruk

Well-Known Member

TimC

New Member

timtheenchanteruk

Well-Known Member

TimC

New Member

waldershelf

Well-Known Member

Ham Salad

Active Member

Similar threads