Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
Cable price looks wrong, should be £20. maybe it includes postage.
The big hit is switching from Disco to P38.
P38 Nanocom
- Thread starter JohnP38
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
The big hit is switching from Disco to P38.
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
- Posts
- 58,170
- Location
- Preston Lancs.
Don't know what it is now but postage costs from Cyprus for my Nanocom unit was about £38.00. Postman must have swam here with it strapped to his back, escorted by two gun boats.
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
That is an absolute rip off.
Obviously trying to pay off the Greek deficit single handed.
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
Is there an alternative?
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
If I had a sample, I could reproduce the cable for a lot less than £50
biggeeeee
Retired - Living the dream
- Posts
- 11,090
- Location
- Lanarkshire or Argyll
If I had a sample, I could reproduce the cable for a lot less than £50
I only have the blue one for the Discovery
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
It may only have a few lines missing, the problem would be identifying which missing line goes to which pin on the Nanocom connector.
- Posts
- 18,961
- Location
- Buckinghamshire, UK. ('95 DT)
Can you not just use a multimeter to check continuity from one end of the cable to the other? Or you think there is some electronics in between?
Jaswilliams
Active Member
- Posts
- 260
- Location
- zummerzet
Found this on line not sure if it is accurate ?
http://www.rangerovers.net/forum/12...ference-between-nanocom-evolution-cables.html
http://www.rangerovers.net/forum/12...ference-between-nanocom-evolution-cables.html
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
How do you check the continuity of missing lines? It may have electronics, but I think not.
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
BLUE--------- Green---------------Nanocom 15 pin
-----------------1-----------------------1
4----------------4-----------------------15&8
5--------------- 5-----------------------15&8
6-----------------------------------------9
7--------------- 7------------------------4
8--------------- 8------------------------5
9--------------- 9------------------------12
----------------11------------------------2
----------------12------------------------3
----------------13------------------------6
----------------14------------------------6
14---------------------------------------10
----------------15------------------------7
16 ------------ 16------------------------14
Might be correct, bit suspicious of the 15&8 connections though.
odyssey
Active Member
- Posts
- 364
- Location
- Derbyshire
Had a quick look at my green cable, both ends are moulded plugs - not openable without destroying them, so BBS have probably had them specially manufactured and are just putting a 'healthy' margin on.
If I get a chance over the next few days to get a new battery for my voltmeter, I'll do a 'pin to pin' continuity chart which should confirm (or otherwise) the previously posted version.
The postage for my nanocom was £27.50 on the discount special offer in Nov '13.
Alastair
If I get a chance over the next few days to get a new battery for my voltmeter, I'll do a 'pin to pin' continuity chart which should confirm (or otherwise) the previously posted version.
The postage for my nanocom was £27.50 on the discount special offer in Nov '13.
Alastair
- Posts
- 18,961
- Location
- Buckinghamshire, UK. ('95 DT)
Pin 1 LHS - check all pins RHS for match (0 ohms). If no match then no way through.
Pin 2 LHS - check all pins RHS for match. If no match then no way through.
Pin 3 LHS - check all pins RHS for match. If no match then no way through.
Or am I missing something?
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
Yes, which pin at the OBD end goes to which pin at the Nanocom end?
The list I posted may or may not be correct, get it wrong and it may damage the Nanocom.
Castor
Trainee maniac
- Posts
- 669
- Location
- Ebley, Glos.
OK team - make a decision for me.
Nanocom or a set of off-road tyres?
Nanocom or a set of off-road tyres?
PPP38vouge
Active Member
- Posts
- 411
- Location
- deddington, oxfordshire
Nanocom, can't take her off road when it breaks.
Datatek
Well-Known Member
- Posts
- 43,928
- Location
- Near Poitiers SW France
Castor
Trainee maniac
- Posts
- 669
- Location
- Ebley, Glos.
private_user
Member
- Posts
- 25
- Location
- New Zealand
@odyssey Did you ever get around to checking the connections on your green cable, or can anyone confirm that they've made a cable up according to the posted detail and have it work ok?
I'd also be interested to know if anyone has discovered what the pinouts are for the CAN BUS cable?
I've managed to save the pennies for the main unit but with postage etc the cables work out to be a bit prohibitive...
Thanks PU.
Similar threads
