mig welder

wickford90 · Jul 31, 2011

I am looking to buy a second hand mig welder, I know bugger all about welding but fancy doing some so any advice on what i should be looking for. have seen these are they ok for novice welder. what money should i be looking to pay for a second hand unit.
uk/ws/eBayISAPI.dll?ViewItem&item=130553546243&ssPageName=STRK:MEWAX:IT#ht_551wt_1141
eBay - The UK's Online Marketplace
eBay - The UK's Online Marketplace

Fur Trapper · Jul 31, 2011

good luck, pray real hard, and practice and practice

666 george · Jul 31, 2011

A grinded will become your best friend. If you want a good weld, give it to someone who knows how to weld, but most of the time you won't see it. So give it a go, you'll love it.

Fur Trapper · Jul 31, 2011

Welding helmet with a # 11 lens, welding leathers, leather gloves, grinding shield, wire brush and chipping hammer, 24 oz ball pen hammer, c-clamps, mole grips, flash lite, various cold chisels and punches and this is just for a starter

jamesmartin · Jul 31, 2011

you will find it easier with bigger set ,with more control of current,a biiger welder will often turn down more for thinner sheet

Fur Trapper · Jul 31, 2011

get one with gas

wickford90 · Jul 31, 2011

jamesmartin said:
you will find it easier with bigger set ,with more control of current,a biiger welder will often turn down more for thinner sheet

the ones i have been looking at have had 6 settings from 35 amps up to 150 would this be ok its only going to be used for minor things, that dont need to look to pretty

jamesmartin · Jul 31, 2011

the bigger the better generally

Sean · Jul 31, 2011

jamesmartin said:
the bigger the better generally

unless it won't turn down enough for thin sheet

jamesmartin · Jul 31, 2011

a larger general workshop welder will often have better more controlable transformer that will weld thinner sheet that those little welders

Sean · Jul 31, 2011

jamesmartin said:
a larger general workshop welder will often have better more controlable transformer that will weld thinner sheet that those little welders

suspect the OP will need to add a trailing zero to his budget for one of those

Fur Trapper · Jul 31, 2011

wickford90 said:
the ones i have been looking at have had 6 settings from 35 amps up to 150 would this be ok its only going to be used for minor things, that dont need to look to pretty

you don't want it to look like chicken **** and you want it to hold you need penetration:doh:

jamesmartin · Jul 31, 2011

you can get cheap second hand ones ,but im just saying to get as near workshop std as possible ,i used to have small snap on one absolute useless for anything less than chassis work so was no use at all on bodywork

Sean · Jul 31, 2011

and if you get a BIG machine you'll not be running it off a standard 13A outlet

Fur Trapper · Jul 31, 2011

Sean said:
and if you get a BIG machine you'll not be running it off a standard 13A outlet

you do not know that you are guessing, you don't have all the facts. what is the amp draw a 230 volts?And James didn't say a BIG MACHINE, larger should work on your 230 volts circuits as they would draw less than 30 amps like your water heater or electric heater.

The Mad Hat Man · Jul 31, 2011

except all our 240Volt sockets are rated at 13Amps

jamesmartin · Jul 31, 2011

thats all that runs mine and its a proper workshop one

fanatic · Jul 31, 2011

The Mad Hat Man said:
except all our 240Volt sockets are rated at 13Amps

Really I have a 16 amp hookup and a certificate by myself to prove it

Sean · Jul 31, 2011

john winsemius said:
you do not know that you are guessing, you don't have all the facts. what is the amp draw a 230 volts?And James didn't say a BIG MACHINE, larger should work on your 230 volts circuits as they would draw less than 30 amps like your water heater or electric heater.

who will rid me of this tire ..........

ya knows the rest

Sean · Jul 31, 2011

The Mad Hat Man said:
except all our 240Volt sockets are rated at 13Amps

he could put a 30A fuse in the plugtop

mig welder

Well-Known Member

Banned

Well-Known Member

Banned

Well-Known Member

Banned

Well-Known Member

Well-Known Member

Banned

Well-Known Member

Banned

Banned

Well-Known Member

Banned

Banned

Well-Known Member

Well-Known Member

RESPECT IS EARNED, BEATINGS ARE FREE ;-)

Banned

Banned

Similar threads