matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
i hate using garages but if i wnt them off i going to have to go to one ive done about as much as i can do
Hdc
- Thread starter matt1295
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Bromsgrove Defender
Well-Known Member
- Posts
- 5,759
- Location
- Out to lunch
Shirley you've just missed something....
Have you read all the three amigo threads ??
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
So no ABS light?
What about the accelerometer question?
What about the accelerometer question?
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
no abs light light
my brake light switch is 2 pin so not switch to fault mine is a 2000 l series
my brake light switch is 2 pin so not switch to fault mine is a 2000 l series
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
Matt...
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
if thats the thing attached to the top of the accelerator pedal then it has one lol
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
Check this is connected ok: Click here...
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
is this under the center console/ handbrake trim
i thought you meant a thing on the accelerator pedal
also my abs light isn't on
i thought you meant a thing on the accelerator pedal
also my abs light isn't on
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
Yes it's near the handbrake. Sometimes they get knocked loose if you take the centre console off.
Does the ABS light come on at all?
It's meant to come on at first and only go out when the car reaches about 5 mph.
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
my abs light comes on when the ignition is started then goes out a few seconds later
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
I assume that's when you start moving?
If so looks like the sensors are ok.
If not that's just weird - maybe ECU is knackered? No idea.
The sensor generates a voltage when the reluctor ring on the drive shaft spins. This is picked up by the ECU. If it goes wrong you get a "voltage out of range" or something like that which makes the light come on. Not sure how the sensor could send a voltage if the car isn't moving though...
Most likely it is the brake switch though, as others have said.
The new type switches usually come with a small adapter loom for the old connectors.
Some models have 2 switches but I think yours will have 1.
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
my abs light goes out maybe 2 seconds after the ignition is turned on moving or not
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
I just read the manual:
"The warning light should illuminate for a short period as a bulb and system check when the starter switch is turned to position 'II' and then extinguish (the light may flash during this period)."
So it looks ok!
Not what happens in my car though.
Do your brake lights work?
Read this post.
Last edited:
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
thats good to no bout my car these 2 bulbs were removed when i bought it which i wish i had noticed as i would have walked away.. spoke to a garage and they says the codes will be £10 to get so having to go tomorrow at 12
just would have being nice to have fixed this myself
just would have being nice to have fixed this myself
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
I would really check the brake switch.
It might just need cleaning.
It might just need cleaning.
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
i have the early brake light switch only 2 pin and only works the brake lights nothing more
matt1295
New Member
- Posts
- 1,734
- Location
- Scarborough
Fault is TC mod switch high volt input.............. where do i start looking
- Posts
- 1,520
- Location
- Somerset (but I'm a Landanna)
Similar threads
