Freelander 1 Freelander 1 1.8 loosing power

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Hi guys..

Quick thing..
I got these plugs from the parts store last week.. NGK BKR6E-11
I see the plug you guys recommend is a NGK PFR6N-11

They both have a temp rating of 6 and a gap size of 1.1

Whats the difference then?
 
Oh yeah..

Just an update regarding the inlet manifauld.

Instead of just replacing it I took gasket maker and sealed all around the seems..

Will test when it is fully cured and update
 
The NGK site lists them as the same temp' range, '6'. The platinum have a smaller centre electrode 'fine wire' according to NGK and the Nickel core is larger with a V cut to enhance spark - looks like both are gapped to 1.1mm
 
Quick question...

Could this misfiring issue be cause by a faulty connection on the harness where the harness from the ecu and the engine connects? Like a dry connection
 
Hi Rob..

Yeah.. I'm now trying everything to sort my car..

What makes it strange is that it is intermittent.. It comes and goes and that makes it hard to diagnose..
 
Hi Rob..

Yeah.. I'm now trying everything to sort my car..

What makes it strange is that it is intermittent.. It comes and goes and that makes it hard to diagnose..
I said at the start of this thread it sounded like a bad connection somewhere and the engine harness would be the first place to look.
It might be worth spending some time pushing and pulling everything in sight while the engine is running to see if you can provoke it.
 
I said at the start of this thread it sounded like a bad connection somewhere and the engine harness would be the first place to look.
It might be worth spending some time pushing and pulling everything in sight while the engine is running to see if you can provoke it.

I've got a similar random issue with my auto box, which I'm convinced is a bad connection somewhere. Intermittent faults are the worst to find. :mad:
 
Lol mine did that for ages and drove me feckin nuts, turned out to be the lambda sensor.

Try unplugging the pre cat lambda and drive it around for at least half an hour. If it’s all fine it’s the lambda sensor.

Mine only did it once it was warmed up. And the lambda appeared to work fine on live data as it switched away fine.

Rossco
 
Oh and if that doesn’t solve it I know there is a common wiring harness issue under the throttle body. Can’t remember what the wires went to though.
 
So looking at this 1.8 misfire now. Similar to above. Have cleaned and gaped plus, checked leads and connections and cleared faults. Was showing cyl 3 and 4 misfire and misfire low fuel. Now just brings up a random cyl misfire. Car idles well, revs well, drives fine up to about 30mph then hiccoughs and flashes eml. Reduce speed and all is well. Meet an incline and power is down badly.

Will try to read fuel pressure. Not sure if i930 will read 1.8k?
I'm thinking fuel pump /filter? Any other ideas please?

Certainly feels 'held back' at speed or on hills. Everything else seems OK.

Will subs a spare in tank pump and filter unit next I think.
 
Will try to read fuel pressure.
You need to read it with a mechanical gauge on the fuel rail.
Not sure if i930 will read 1.8k?
I'm thinking fuel pump /filter? Any other ideas please?
The ECU doesn't monitor the 1.8 fuel pressure, as it's not needed due to exhaust gas monitoring. The fuel pressure needs to exceed a minimum 3.5 bar at full power output.

Certainly feels 'held back' at speed or on hills. Everything else seems OK.
Try the fuel filter first. It's known to clog up, and reduce fuel pressure as a result.
 
Yeah the pumps and the o rings inside them that seal the filter can be an issue. I had to replace mine at one point.

Do you know if the fuel filter has ever been done?

Rossco
 
Sorted. Rob gets the ice cream this week! Having remade all the electrical connections and the problem only being on hills, I changed the fuel pump!! No improvement and a repeated cyl 4 misfire code. Changed 1 and 4 coil pack and bingo.
What did I learn, a face-lift fuel pump makes a pre face-lift fuel gauge work in reverse and getting the fuel pump ring on is difficult. Made worse by the fact that it didn't need doing!!
Thanks for all the input everyone.
 
Glad its sorted Andy - I had to replace both coil packs on mine for intermittent misfires within 6 months of each other. It's run as sweet as a nut ever since. The spark will break down under heavy load, so hence the misfire on acceleration. On mine, it was worse on acceleration from low speed in a high gear.
 
Back
Top