Search results

Mine did afer my head gasket went causing overheating problems. I think one of extra the senders on the thermostat housing controls them. Dont know what temp they are set to cut in at though. I am going to remove my aircon rad but leave the leccy fans in place. Gaz

There appears to b e little by way of adjustment internally on these pumps. It all apears to be external via the full power screw, boost compensation and the setting of the timing advance etc. To change the HP head (distributer head) I only need one O ring which I should be able to get from...

Bought a seconhand mech pump to replace the EDC type I had. All OK but disco diffcult to start when hot. If I pour cold water over the injector pump it then goes OK! This would suggest that the HP pump head is worn and cannot produce enough pressure when hot due to increased clearances. I have a...

so are these not available then? Gaz

Anyone know where I can get a rebuild kit from for a mechanical bosch VE pump? Gary

recent overheat due to head gasket/head failure (cracked). I think the original overheat was as a result of the P gasket failure some time ago! rimmer bros are offering the new LDF500180 at £370 ish complete, island 4x4 the old ERR5027 at £300 ish Gaz

so which replacement head do i go for to bring my 300tdi back to life? Apparently LDF500180 has better cooling ports or is this nonsense? Are the britpart heads any good? Gaz

so swapped the battery for a newbie (the biggest I could fit). Will start now when cold but wont have it when hot!???. If I max out the advance on the pump then it goes but only if jumped and after it has been left to cool a little... Dont think engine overly worn as it used to start easy hot...

So I recently replaced my injector pump with a non EDC variant and now am having starting problems. The engine goes first time if jumped but will not start on its own even though it seems to be turning over fast enough. Priour to the pump swap it didnt need to turn over very fast at all to...

I have got hold of a bosh err4419 to replace my err6727 Kickdown already there, can I not convert the standard footpedal for a cable? Throttle pot no longer needed I take it? Gaz

So after being let down by my disco over the weekend (came to it and it would not open with the key fob, used key to gain entry but would not start, 2 days later still nothing) I have decided to get rid of as much of the electronic cr*p as I can.Starting with removal of the fly by wire pump to...

mine is definitely fly by wire but there is no three wire box on the back if the pump. It has a plastic box on one side nearest the engine with loads of wires going to it. I took this off (or tried to) had to drill out one anti tamper bolt but lifted the box as far as it would go but no selonoid...

still no joyt with this,,getting ready to bin it, Deffo no spider but the injector pump doesnt have the three wire dds thingy. There is a plastic rectangular thingy on the top with a load of wires going to it and a couple of wires that go to something underneath and a single wire to what looks...

never had any probs till now, dont think its a jap import...many owners and lots of history. I am only of the opinion that it is EDc cos of no spider. As i said ripped out dash and nothing there..... Apparently you can 'work around' the fuel pump intelocks??? but I was looking for a more...

hoping someone on here may be able to help!!! I have a N (96?) disco auto 300tdi. This morning when I went to it the key fob (2 key version) would not open it. So I used the key to open the drivers door. Put the key in the ignition, the engine spun but would not start. Imobiliser light was not...

Apologies its a 300tdi 1995 Gaz

Got a rattle whine from something on the fanbelt drive train as the noise dissapears when the belt is taken off. Have changed the water pump (twice), the belt tensioner bearings and checked the power steering pump and alternator (both OK). been doing it for 8 months or so and has got no worse...

Does anyone know where I can get some of those aluminium door bottom/front and rear panel bottom protector panels from? regards Gaz