Search results

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
  1. W

    Best way of removing siezed bolts?

    what was wrong with the scafolding bar ? :whoosh:
  2. W

    Roof frame wanted

    cant you use the cahe as a support ?
  3. W

    Best way of removing siezed bolts?

    if you have some scafolding bar slide it over the spanner/ rachet handle and stand on the end :) ( if there is enough room ) to fit it on
  4. W

    Flip front conversion!!!

    thanks :) all of the panels are of now so its just a case of putting them back togeather ( :o daunting much? :p)
  5. W

    harness mounting points

    a big bolt going through your chassis at the back of your tub might give you a goon enough angle but then you have rope going across your tub:(
  6. W

    Flip front conversion!!!

    howd u do that ? did you just make up a frame to sit it all on or just bolt them all togeather ? and where about did you mount the hinges ? thanks
  7. W

    how to fit spotlights

    thanks for the diagram, its realy helpful and i shall fitt them next weekend :)
  8. W

    how to fit spotlights

    haha yh i was going to rub off the paint around the hole in the bumperand earth them to that. please gan i have some pointers on how to take a relay off of the main beem as this will be the first time i will be using a relay thanks :)
  9. W

    how to fit spotlights

    thanks just wanted to be sure before i turend my car in to a fireball :p
  10. W

    how to fit spotlights

    hey, iv been given a set of spotlights but they dont have any diagrams with them :( at the moment they have an earth and a live wire comein out of the back of each one, i want to run them as a pair so would i be right in thinking that i attach the earths to eather the negitive terminal or...
  11. W

    harness mounting points

    thank you alot for that, work will begin soon as the seat box is comming out soon :)
  12. W

    harness mounting points

    hi iv decided to go for racing seats and harneses in my series 3 with a truck cab please can someone tell me how to mount the harnses and seats. i hope to eventaly have a roll bar/ cage but i dont have one at the moment. thanks
  13. W

    rust undre the windscreen :|

    thankyou. ill get in touch with the fabricatot down the lane :)
  14. W

    rust undre the windscreen :|

    hi, ive just tsken off the windscreen and underneath is rusted like hell :doh:, there are 4 or 5 bigish holes 7 cm x 4 cm and alot5 of corrosion that has not yet gone through. is this a easily replacable bit of the bulk head , or am i better patching whats bad till it falls apart or will i...
  15. W

    Spark plug series 3 info

    0.8 mm i think ( dont quote me on that) the guy where you get em from will no though even though mine were sparking i had to replace them and it fixed the problem apparently they wont work under compression but will out of the sockets :)
  16. W

    Project Series 2A

    thank you cleaning the box up anreplcing the fliir is a weekend job then :)
  17. W

    Project Series 2A

    hi please can you tell me ruffly how long it took you to remove the seat box tunnle cover and floor ? thanks
  18. W

    Clutch slave cylinder and union

    i thought about the metric thread i was wondering if it would be easyest to put anothe new slave in or replace the pipes ? :\ oh i should probably have added that the flare o the end of the pipe dosent fit.
  19. W

    Clutch slave cylinder and union

    h i i have recently replaces my clutch slave cylinder on my series 2a with one i bought from paddocks. the slave fits fine however the pipe from the master will not go in the hole. do i have a duf slave or do i need to replace/ file down the flare and union ? sollutions...
  20. W

    Land Rover Series III - Battery Earth Strap

    mine bolts on directly to the chassis right next to the clutch slave cylinder :) works fine
Back
Top