Search results

Hi,I am using redundancy to start a new venture and I am looking for reasonable motor trade insurance cover. Has anyone managed to get a reasonable quote without combining private motor insurance. Bri

Hi I was looking for some parts for a late v70 volvo and a merc . I came across 2 land rover 110 s breaking. If any use for anyone. they are in shildon near bishop auckland and are pretty cheap for parts if you take them off yourself.

Hi does anyone have any names of sensible insurance companys to use after a ban for a 22 yr old with DD40. Direct line will not insure. Getting some silly quotes for car insurance. The offence was on a bike and thats only £178 to insure. He had 5 yrs without any claims as anamed driver. Ta Bri

Any one know where to buy a decent replacment cat. I can only seem to find the cheap ones locally. Ta Bri

Anyone know how to trace a location of a series 2a. I have been on direct gov tax enquiry and it was last taxed in the 90s. I am curious as it belonged to my father who passed away recently.

I believe I may have an overheating caused by IRD (gets boody hot). K series can tick over and be below half on gauge for 1 1/2 hrs. Take it long run 30 miles and it will boil over. I am asking if anyone has had a similar prob caused by VCU overheating IRD/coolant. Can this be confirmed by...

Hi all, I am going to start looking for series land rover for my sons 21st. I dont know what sort of money they go for. In reality they vary considerably. Not an issue working on one as long as it is roadworthy ish:blabla:. Ta Bri

Completed a compression test on freelander 1.8 and all cylinders are 14 bar or just over. Noticed oil level is slightly over the max. I believe they should be at 12 bar max. Has anyone the correct reading I should be getting. I will be draining the oil and re doing test. Thanks Bri:blabla:

Just fitted new thermostat and expansion bottle cap after engine was getting hot towing caravan. when I bled the system i noticed that there was antifreeze from bleed above gearbox but not from anywhere else. I have since ran it and left it running for over hour with no probs. Tonight I drove...

Anyone know where to get a decent Cat converter from for k series. Cheers Bri

Hi all anyone had probs with oil pump. If I drive about 10 mile and sit on idle the oil light comes on. The oil is at max level, Bleep the throttle and it goes out. Cheers bri

I have had my 1.8 freelander on gas analyzer and its reedings are just over required limit. The Vehicle has just had a full service and lamba sensor. the cat was replaced over a year ago. the guy stated this is a common prob with the freelander. Has anyone experienced same and how did they sort...

1.8 freelander wont start, getting fuel to fuel rail and if i disconect fuel reset switch it will run but only on tickover.If i then reconnect fuel reset it will tick over but cut out if throttle is opened. one landy so called specialist said he was beat, but said try a fuel relay. is this not...

any one had any issue with fuel system on a petrol lander. fuel delivered to fuel rail on cranking , but it still wont start.

yet again another prob. was running but began lossing power on banks n hills. when on return journey it lost power and if throttled it i cuts out and wont restart( but ties too) any ideas? its had temp sensor, cam sensor and rota arm n dist cap in last month

driving to get shoppin it lost all power. i got there where mrs was as aa arived. he diagnosed either belt slipped a tooth or head gasket failed. im talking to mrs it didnt overheat was below half on gauge. so when i got home i looked at timing belt. on aligning cams then checking crank pully it...

has any one made a processor, of just used pure veg oil. been researching for a while. and wi running 4 motors. considering changing 2 for diesel

having replaced the obvious on 1.8 petrol freelander,because it took ages to start when cold, but would run all day till next morning. I resorted to have ecu read for any faults . this showed fault on temp sensor telling ecu that the engine was hot when it wasnt, had fault cleared. drove it home...

does anyone know where the camshaft sensor is on a petrol mems 1.8. i can clearly see it illustrated on the mems3 but not on older model