Search results

Hi all, hoping someone has the answer or at least where i should be looking. I noticed that my air compressor has stopped working.. tried the raise button and nothing, does not revel, just dead. I have checked the fuses all good, swapped the celanoide with identical one next to it and still...

Hi all.. I need a bush for the front ace actuator and cant find anywhere hoping someone can help.. its the one at the back of the actuator not the one one the shaft... The ace has actually been capped so would like to consider removing the front ace actuators and fitting a proper anti roll bar...

Hi All I have a problem i'm hope your collective knowledge might help me identify the issue. Increasingly often when i go to start the disco it just clicks, very much like a car with a totally flat battery, but after trying a few times she suddenly fires up and turns over like the battery is...

I want to add more preload to the waste gate on my D2 auto TD5, I have read up on how its done and i have already added 2 turns and its made a difference.. but reading more many keep adding until the ECU senses overboost and kicks into limp mode then backing off a turn.. I want to try this to...

Just a general question really.. The MOT for my D2 is in September.. I plan to take it for it's test 30 days earlier, to give me plenty of time to sort anything that comes up that I was not expecting while still being able to drive on the current certificate.. Just wondering how many others...

Hi all.. Been having some starting issues.. this weekend will be fitting a new injector wiring loom.. have a new fuel filter and air bleed valve for the housing.. but I know another common fault is the CPS and for what they cost I thought may as well change that too.. but is this the right one...

Hi guys.. since buying my D2 TD5 auto 5 weeks ago it has started to have starting issues which i'm trying to sort and looking for some advice.. First it does have the dreaded oil to the ECU problem and I am fitting a new Injector loom and rocker cover gasket this weekend... I don't think this...

Hi guys.. Is there anyone in bury area or Manchester with a nanocom willing to help.. been having starting issues.. pretty sure is the horrible amounts of oil travelling the wiring loom from the injector loom.. that' being changed on Friday.. but I want to know if the ecu has logged any...

Hi all, hope you're enjoying your weekends.. Well last week I posted a thread asking for some advice as I had a incident when my D2 TD5 auto failed to start, then started really rough, engine recovered but she then went into limp mode with the M&S lights flashing... got home ok in limp mode...

Hi all, I have a small issue and i'm looking for some wisdom.. I drove my 2001 D2 TD5 Auto to work this morning all good no issues.. at the end of the day I gets in and it wouldn't start straight away, never done it before.. took a couple of goes, started but really rough, couple of revs of the...

Ok so my 2001 D2 ES auto has ACE fitted but it has been disconnected but not removed.. It has anti roll bars front and rear and it actually corners quite well (not as good as my last D2 that had working ACE) so I think I can safely presume who ever disconnected the ace added standard anti roll...

is it part of the fuel system?.. located on the O/S chassis under the B pillar... as you can see its leaking slightly so needs sorting.. would it be easier to repair or replace? once i know what it is of course Nige

Stearing on my 2001 D2 is vague and wonders a little.. checking it there were 2 problems, UJ that tightens onto the splin shaft of the stearing box was loose, tightened this and all good there now and has fixed some of the issue, but there is one of the track rod ends N/S that is worn.. so i...

Is there anyone near Bury or Manchester with a nanocom or Hawkeye that could run a check on my landy see what shows up.. Could swap for some welding services or something.. don' have one and they are out of my budget right now Nige

I had a welding threat going but thought i would start a fresh as this is specifically Land Rover related... A little background, as a day job I teach welding, fabrication and sheet metal at a training centre in Oldham near Manchester and i thought I would do a series of "how to" posts and...

My 2001 D2 has a constant fairly loud whirring noise from the rear of the vehicle.. It doesn't sound like anything wrong its a healthy motor running whirring but its quite loud... at first i didn't think anything of it as it has been there since i got the vehicle early last week. but yesterday i...

Just want opinions on whether its worth doing... YET!!! My 2001 D2 TD5 is well looked after (only had it 5 days) chassis is mint, it's still on air suspension which is working great, no leaks does what it should.. my thoughts are wait until the airbags start to give me issues if at all and THEN...

Hi all, I recently got a gorgeous D2 TD5 2001.. I ordered an EGR delete kit which arrived today.. looking forward to spending saturday morning tinkering and fitting the kit.. but i read earlier that there are different TD5 engines and that from around 2002 they went from P10 to P15 engines which...

I just bought a 2001 D2 TD5.. I wanted one that was cheap because it needed welding.. That might sound a bit crazy to some but I'm a welding instructor so for me an easy job. Irony struck and I ended up getting a gorgeous D2 which has been waxoiled every year and has a mint chassis.. not a bad...

Hi All, just joined the forum as I have just again joined the ranks of Disco 2 owners. I had one 18 months ago, drove all over europe in it but had to sell as i was skint... Finances now better and after much searching I found a gorgeous 2001 D2 TD5 ES, everything works (well almost), engine is...