Search results

hi, since Sunday I’ve had a problem with the landy starting in a morning. I get in, turn the ignition on and off a few times in this cold weather, Then start her up. She’s been spot on until Sunday morning, turns once and fires but it just turned over without firing. So I stopped, tried again...

So after my recent rebuild I’ve managed to get her out on the road for a few miles to see if there’s any problems. 1. The temperature gauge doesn’t seem to be working, the heaters get sort of warm compared to on start up. I’ve put an earth on the wire at the temperature sender and the gauge...

I purchased it about 9 months ago brand new (about £50) I then went on to replace the bulkhead and not bother repairing it, so I have the repair section that replaces the top of the bulkhead from the top hinge holes to the middle of the bulkhead at the other side of the vent. One of these...

Removed from my 1987 90 (copied from eBay).... Goodyear Wrangler MTR tyres 33x12.5x15 There are 5 altogether. The 4 tyres on the vehicle have around 14-15mm of tread and the spare has around 12mm. They’re in excellent condition, I’m only selling them as I won’t be doing much off-roading so...

Hi, just putting the feelers out there. I have 5 Goodyear mud terrain tyres in excellent condition on my 90. I won't be doing much off-roading, more greenlaning and the commute to work so I would prefer some all terrain tyres. My tyres are 30/12.5/15 (I think, trying to remember off the top of...

I have the bit that sits over the gear stick etc but I need the part in front of it that bolts to the bulkhead and sits over the bell housing part. I'm also on the lookout for two front doors for a 90. Thanks in advance

Hi, asking for a bit of advice on behalf of a friend. The motor in question is a disco 1 300tdi. The problem is the rev counter is jumping from 0 to idle whilst the battery light flickers? And if you stand outside of the vehicle you can hear a slight change in the engine noise, like a slight...

I'm in the process of wiring the 90 back together (1987). When I bought it no gauges or lights worked. I've managed to get most of the lights working along with things like interior clock and 12v cigarette lighter. I've just got a few small issues left to sort which I'm stuck with. Firstly the...

if anyone could help me out please... Firstly is the bolts that go through the side panels into the tub, the ones with the big washer in the middle. I believe they're known as hard top mounting studs but they do a short one and a long one. which ones are for a 90 with van sides? Secondly...

hi, I have a 90 with a 200tdi engine. I've got a new (second hand) heater box as my original one is seized. Now whoever has removed the old one of the donor car has just cut the cables and my old cables are no good. I've tried searching for new cables but can only find a heater control cable...

Hi, I have a 90 and have taken apart the front suspension, wasn't too much of an issue but one of the top nuts on the shock absorber was seized. I managed to get it off without damaging the thread so I just need to locate a new nut. After a search online I've found I need a m12 x 1.25 (I...

Hi, I've been lurking around for a short while so thought it was about time I started a project thread seeing as I can't keep my nose out of everyone else's. Any help and advice would be much appreciated! A little bit about myself and the 90... I'm a painter in the motor trade and last year I...

Hi! I'm Ash, from the North West. I bought a 1987 90 last year which needed a bit of tlc. She has a 200 tdi engine and a galvanised chassis which was a good a base as any I believe. I'm new to the Land Rover scene but with a bit of help from a friend who knows plenty and the knowledge on here...