Search results

My transfer box has been leaking for years and rumbling for a while too, I decided to buy a rebuild kit from ashcroft. Followed the manual but used the shims that were in it. The vibration/rumbling has gone but now a get a clunking sound when the engine starts and when under load. The box has...

Ive been trying to pinpoint my vibration at 1500rpm. So far ive done all the wheel bearings,rebuilt the swivels,new rear prop rubber,front prop uj's,rear uj's are fine,checked the phase of the front prop. With the front prop off the vibration goes,with the front prop on and diff lock...

I forgot to plug the alarm sounder back in,was off for a while but now when i plug it back in it wont stop sounding off. What should i check first? :)

I followed the workshop manual exactly but it runs like ****.Its like driving with the brakes on and a **** load of smoke. I took the front cover off to check it all and it all looked good. The only problem i had (if it is a problem) was that the locking pin that came with the kit (9mm) would...

No idea what its worth,comes as seen with two hella spot lights which will need bolting back on. (Comes with the bolts) £100 located in blackpool,open to offers. pics on the ebay page. Land rover discovery 1 Safari front bumber with Hella spot lights | eBay

No idea what its worth,comes as seen with two hella spot lights which will need bolting back on. (Comes with the bolts) £100 located in blackpool,open to offers. Its not lettng me upload pics on my phone so ill upload it when i get home. Same as this one...

My mate pressed the clutch pedal like a knob and the slave cylinder lost fluid. Ive tried bleeding it but it wont go in gear,the pedal doesnt seem as hard to press as it did before. Ive removed the slave and checked the push rod is on the fork,tried bleeding it again but no luck. Also when i...

I have a winch bumper and a steering guard on rhe front and nothing on the back,might get a winch in the future. Ill be getting 2" dampers and springs but the medium duty say it for an extra 500kg weight on the back but i wont have that much weight or anywhere near it. Should i fit medium...

Coming towards a roundabout down a bridge and my brakes failed,foot the the floor. Got it home and the front part of the reservoir is empty,i had a small leak on the front ns caliper which i was planning on doing at weekend but it was a very slow leak which is why i left it. The front part...

One of the rear lights has stopped working,its not the bulb and its not the connector. Its not even getting any volts to it but the other side is. Problem i have is that mine only has the two lights in the bumper and the ones thats working has some of the red missing. I would imagine...

'Ive ordered a light bar and 4 18w led spots. Am i best using an inline fuse or one of the relays with the fuse built in? I want to use one wire each for the +- rather than having to route loads of wires, will 6amp wire be ok or should it be a little over rated? cheers :)

Ive seen 8,9 and 10mm seals and both mine leak,also i checked my wheel bearings and one was bone dry and the other was **** wet with oil. How do i know which ones i need? cheers :)

So i've finally got a bottle for my welder so i'm going to have a go at the holes in the footwell at weekend,should i butt weld a plate in or cut out the rust and seam weld a plate over the hole?

I thnk my power steering pump has shat itself,I've noticed my steering has been a bit heavy and now the pulley is loose and has been putting pressure on the belt and it sounds like there is a bearing rattling around it in. I've seen a brand new on on ebay for £55 delivered (wolf brand I...

Been looking at getting a new caliper instead of a used one as they cost under £40 delivered. Are they any good or should I look for a used one? DISCOVERY 1 300TDi / V8 94 on RIGHT HAND REAR BRAKE CALIPER SMC500110 | eBay Cheers

Got a hole under the rear body mount on both sides of the chassis,will the mount need removing to do a proper job?

When I bought the car I was told the air con had "seized",I wasn't going to bother using it so I removed the air con compressor. Well its getting warmer and I want the air con :D I need to replace the clutch bearing but can only find them for sale in the US and all the bearings from the...

Having some issues with my cb and from what I've read it may help running it direct to the battery pos/neg terminals,I also want to hook up a amp for a sub and there is bound to be other things in the future. What's the best way to do it? Is there so e kind of fitting I can replace the...

I have a discovery 300tdi and the previous owner said he had defender callipers on it,I need to order some pads and a rebuild kit but It has no markings on it. Cheers :)

Need to order some pads and a rebuild kit for the n/s caliper,when I bought it the guy said the brakes were upgraded to those from a defender. I had a look and couldn't see any markings so im hoping one of you guys can tell from this picture :)