Search results

Didn't know how it worked sorry. . .😕

Thats on axe edge, just outside of buxton on the leek road. I work down the road from there. Only just seen the thread, could of nipped up after work with my mate and given a snatch out. I've got a winched up 90 and my mate a 110 with winch and ARB's. Bloody typical, 😔

I got the fuel filter aswell, to be on the safe side. Blew the fuel line out with the airline to make sure it was clear whilst i was doing.

All sorted, lift pump was knackered. Bobbed a new one on and away she went. Happy days��

Thanks, was going to chance a lift pump for 20 ish quid. I will check them aswell tomorrow while i am doing. Need to get the old girl back up and running as my other option is my motorbike, don't really fancy skating down the road on my ass on the ice.☺

Hello guys. On my way to work this morning my defender with 200 tdi disco engine in went very sluggish and wouldn't pull. I've checked all intercooler pipes etc and the turbo, they all seem fine and as they should be. When i took the pipe off the fuel filter housing down to the lift pump and...

Hello guys and gals. Does anybody know why none of the chassis manufacturers make a galvo chassis for the Tdi Disco's. I've seen chassis' for the Td5's and pretty much every other land rover series and defender etc but no one seems to do one for that disco. .. ? Wondered if there was some...

Hello guys, I've bought some of them Glencoyne engine mounts for my 200 tdi disco engined 90. I was going to change them this morning, i have undone the nuts on the mounts thinking I could jack the engine off the mounts and slide the new ones in. . . Is this possible?? Or do you need to take...

Hello, if its the one i'm thinking of its just off St Mary's way in Stockport near the Portwood roundabout. Its on the left as you head towards the roundabout and the M60. Hope thats of some use. . .

Morning all, Driving to work this morning it felt like there was a Vibration underneath my 90. I've just had a look when i got here and it feels like there is play in the bearing on the transfer box that bolts to the front of the rear prop. The transfer box and gearbox have come from Ashcroft...

Thanks guys. I'll do a bit of searching, see what comes up.

Hello there. Not been on here for a while, I was just after thoughts/opinions on whether to wax oil or stonechip a galvanised chassis. Would you guys bother or leave it as is. Any thoughts or opinions etc would be much appreciated. Regards Ewd mucker.

I lathered the UJ's on the column last night with a load of spray grease to see if that makes any difference, i would be surprised if the box is at fault on mine because its done so little mileage and is only about 18 months old. I'm going to see what thats like today and take it from there.

Its got a 200 Tdi in it from a disco, i have looked at the receipt for the steering box from when it was re built and it is listed as a 6 bolt PAS box. Its only done about 2500k on the land rover.

Hi, to clear misting from the inside of the glass, get some insulation tape and tape up over the lense on the outside and then turn the light on, the heat inside the light clears the glass, but be careful not to leave it on too long as it will get hot, just keep an eye on it as you do it.

Morning I 've got a fully re built 90 and its got a new power steering pump fitted to it, the steering feels quite heavy to me, it does have a smaller steering wheel fitted but even with that i would still say its heavy. Its got plenty of fluid in, so i was wondering if the pump was adjustable...

I've managed to get a decent peddle which up to now seems ok. (Fingers crossed) the idea of filling the system from the bottom seems like a good one to me, and if it works then surely that's a good thing. I will give that a try if i need to do one again.

Evening Folks, I've changed the clutch master cylinder on my 90 this afternoon because the old one was leaking fluid down the pedal, when I was bleeding it up I had a bit of trouble getting the pedal to pump any fluid through with the nipple open. I managed in the end to get it to pump the fluid...

Nice one guys. Thanks for all the helpful info, it's much appreciated.

Ok. Just to make certain in my head. Would you use a relay for the side light circuit and relay for the main beam circuit or do that for each side making 4 relays in total . . .??