Won't move!
- Thread starter l666mud
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 16,475
I almost fell over backwards with the amazing level of detail you have gone into with your post, unfortunately my crystal ball is in the shop for polishing so we will all need a bit more info to work on....
Car won't move or EAS??
Diagnostics is first step , obviously, to find out why the thing has dropped to the bumps...
Do you have the four lamps lit and 35mph warning on dash??
Car won't move or EAS??
Diagnostics is first step , obviously, to find out why the thing has dropped to the bumps...
Do you have the four lamps lit and 35mph warning on dash??
- Posts
- 58,170
- Location
- Preston Lancs.
No it's not normal look at the "How to" section and check operation of compressor and other parts of system as laid out there.
l666mud
Member
- Posts
- 48
I almost fell over backwards with the amazing level of detail you have gone into with your post, unfortunately my crystal ball is in the shop for polishing so we will all need a bit more info to work on....
Car won't move or EAS??
Diagnostics is first step , obviously, to find out why the thing has dropped to the bumps...
Do you have the four lamps lit and 35mph warning on dash??
Yes, all lights lit and speed warning on dash. After parking up it goes into gear but won't move? Got me beat?
- Posts
- 58,170
- Location
- Preston Lancs.
- Posts
- 16,475
How long has it been parked up?? Could it be the transmission brake shoes have rusted to the brake drum?? or the pads rusted to the discs??
Could it be the parking pall in the gearbox not releasing the parking brake disc??
Does it engage a gear..i.e. you can feel it take up the drive?? or does it just rev freely??
Do the checks as per the how to on the EAS system and get some form of diagnostics once you have done the basics!
- Posts
- 16,475
Highly unlikely as the two systems on the P38 are totally separate...
On the L322, the systems both talk on the CANbus and although the TB would log a fault on the CAN, it wouldn't cause the thing to be stuck dead...
I think he is looking at your wallet rather than the fault!....but I stand ready to be corrected and amazed at this new phenomenon....
Datatek
Well-Known Member
- Posts
- 44,138
- Location
- Near Poitiers SW France
As Saint said, no connection between EAS and transfer box.
Datatek
Well-Known Member
- Posts
- 44,138
- Location
- Near Poitiers SW France
Fuse 11 under drivers seat
- Posts
- 16,475
- Posts
- 16,475
So what was the problem...not posting the solution renders the point of the forum useless as it help no one!All sorted, all faults cleared and back on the road, my wallet not that badly beaten either
- Posts
- 19,010
- Location
- Buckinghamshire, UK. ('95 DT)
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
- Posts
- 58,170
- Location
- Preston Lancs.
+2, or are you to embarrassed ? was it fuse 11
Couldn't really have been a lot else.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Couldn't really have been a lot else.
He might have left a wheel on each axle jacked up.
- Posts
- 58,170
- Location
- Preston Lancs.
He might have left a wheel on each axle jacked up.
Not if he has traction control.
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Last edited:
