Winch Bumper with Mod finished and fitted :-)
- Thread starter StuRox
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Or for even opening the gate to my office car park
Ha ha. I do the same with me transit bumper
Deacs
New Member
- Posts
- 28
- Location
- Dunstable Beds
The Disco 2 lights behind make it look like its wearing bi-focal specs!
Tuff ones though, you wouldn't mess with that
Tuff ones though, you wouldn't mess with that
- Posts
- 14,902
- Location
- Doncaster
+1
Pikey
Dummy Ejection Facilitator..
- Posts
- 47,185
- Location
- in Baron Wet Bum's Slave pit..
look nice. Got the sun in me face at mo but have ya braced the corners of the wraparound to the Bumper I would be inclined to fit 2 bits of tubing to corners of bumper and attach to wraparound Might stop it been shoved backwards into the lights if ya have a hard bump. Mate had a light bump in her disco and the wraparound quite litterally wrapped around and took out her O/S lights and wing. Bumper never moved though.
That is literary my next job - but ran out of gas so couldn't get a good weld for the side braces.
I also want to fit at least 3mm triangle braces behind the a-frame part onto the bumper to also re-enforce it so it doesn't bend into the bonnet.
Hopefully picking up a new gas bottle Tuesday to get the job finished.
Realised I wasn't completely out of gas (even tho the gauges are reading zero!!), but one of the valves had been knocked and turned off
So managed to finish off the bumper today, by using some left over steel I have - 5mm flat and 5mm 90 degree folded...
So started by adding 2 supports to the A-Frame using the flat and the 90 degree steel...
then added to supports to each corner - 1x 90 degree for the corner and flat for the end....
All in all - 8 new supports - probably over kill, but I rather that, than it bend into the bonnet or lights.
Doesn't look that pretty when you look at the supports, but once fitted, you can't really see them - anyway - functional
So managed to finish off the bumper today, by using some left over steel I have - 5mm flat and 5mm 90 degree folded...
So started by adding 2 supports to the A-Frame using the flat and the 90 degree steel...
then added to supports to each corner - 1x 90 degree for the corner and flat for the end....
All in all - 8 new supports - probably over kill, but I rather that, than it bend into the bonnet or lights.
Doesn't look that pretty when you look at the supports, but once fitted, you can't really see them - anyway - functional
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
Make your own then you get it to the spec and shape you want
then you get it to the spec and shape you wantadam300tdi
Active Member
- Posts
- 639
I really like it.alot of protection on the front
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
That bullbar won't help with that, you want an arb. LR original bullbar a aren't the strongest metal but they do well for protecting against light stuff like small branches and light theifs
I do like the ARB ones but the cost is too much.
Im surprised no one actually make just the mounting plates that bolt to the chassis so peeps can them fab their own bumpers. if some one does ive not come across them.
im thinging of using a C beam as the basis of a winch bumper
Im surprised no one actually make just the mounting plates that bolt to the chassis so peeps can them fab their own bumpers. if some one does ive not come across them.
im thinging of using a C beam as the basis of a winch bumper
Dr_evil
Banned
- Posts
- 29,535
- Location
- Perched on the naughty step
It's not hard to make up the plates I made up a batch and used them to build a few from. All you need to do is cut and drill a few holes in some plate, preferably plasma cut.
As to the beam I prefer folded plate, much easier that way
As to the beam I prefer folded plate, much easier that way
