What have you done to your Landie today.

Sirus said:

Looks nice with red flecks of plastic in it

Click to expand...

how did you manage to drive all over portugal with it but when you gets to scotshire you breaks it?

ratty said:

how did you manage to drive all over portugal with it but when you gets to scotshire you breaks it?

Click to expand...

I parked on a slope the other way........you has to drive on the other side in Scotlandshire,,,,,,bloody foriegn place

Sirus said:

I parked on a slope the other way........you has to drive on the other side in Scotlandshire,,,,,,bloody foriegn place

Click to expand...

wanna buy some light guards?

Stick em in your shed on the pile

Sirus said:

Stick em in your shed on the pile

Click to expand...

anything else?

ratty said:

anything else?

Click to expand...

A front propshaft for a 110 would be useful

today I went shopping for a gasket set and timing chain and new head bolts.. forgot to get a fan belt but that's easy enough to change later on..

I then removed all the stuff on the top of the engine down as far as the inlet manifold gasket.. didn't expect to find that under there

hopefully the heads will come off tomorrow... fingers crossed...

got some top notch advice
broke some clips
broke an arch liner
removed some skin
snapped a vacuum pipe

and the snorkel is only half fitted!!! :doh:

In the past couple of days ah've managed tae get everything bolted to the bulkhead, waxoyled the front chassis, got the bulkhead lined up, roof/sides and windscreen bolted down, chassis to bulkhead brackets sorted (no spacers needed), fitted the spare doors to help with alignment, fitted door rubbers, fitted all the dash stuff, connected up the wiring except the front lights as ah've still tae put the wings back on, painted some small bits and pieces and probably a couple of more things while sufferin' the dreaded man flu!

just seen yer piccies buster,lookin good mate.
but wot we need know is a photo repair thread for doin propshaft uj,s so Si can change his :doh:

oil dripper said:

just seen yer piccies buster,lookin good mate.
but wot we need know is a photo repair thread for doin propshaft uj,s so Si can change his :doh:

Click to expand...

Cheers Drippy mate Propshaft uj's... Do ye think this might help him...

http://www.landyzone.co.uk/lz/f41/uj-renewal-59812.html

bustersbus said:

Cheers Drippy mate Propshaft uj's... Do ye think this might help him...

http://www.landyzone.co.uk/lz/f41/uj-renewal-59812.html

Click to expand...

i think it mite


know wheres me fekin glasses

mark it F.T.A.O Ex Fishy Bollics

Not today but yesterday............

I fitted a new aerial and a better stereo!!!

Also lightened it by finding a lot of mud behind the wheel arch liner..........

Today if i get some time i might try cleaning the breather on the engine out AND getting all the tools out of it from yesterday LOL

just found the transfer box output seal at the front is leaking and is ****ed off because when i had the box out i replaced the bugger!!!!

managed to get the head job further on.. all the way to the right hand head being off and bolt 4 on the left hand head rounding nicely...

different sockets on it tomoz I hope and see if I can't get the bugger off.. thank god I bought new ones..

took the exhaust orf, with an angle grinder,
poked a hole in the sill that i could get my hand in, o happy dayz, what next?

removed the floor pannels and gearbox tunnel ready to remove the engine ....

I repaired the front panel, so bad it had collapsed at the bottom, welded in a bit of steel i had well chuffed as it already had the bend in , looks well neat

next job is repairing the ineer wings where the panel has corroded it

Stuck me wings back on, wired up the front lights, fitted the two brackets from the bulkhead to bottom of the wing and sill and a couple of wee odds 'n' ends

mjltigger said:

managed to get the head job further on.. all the way to the right hand head being off and bolt 4 on the left hand head rounding nicely...

different sockets on it tomoz I hope and see if I can't get the bugger off.. thank god I bought new ones..

Click to expand...

Tigger. I have some rounded nut removers. Gis a shout if ya wanna borrow em.