shaunsmith
Member
- Posts
- 46
is there anyway of changing the oil in a viscous coupling
viscous coupling
- Thread starter shaunsmith
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 83,232
- Location
- Embasinga stocæ
what oil?
I think its actaully asilicon gel shaun.
but a good question non th e less. anyone now exactly what it is. Maybe there's a short term fix if someone knows.
- Posts
- 83,232
- Location
- Embasinga stocæ
it is
snot a good Q - its an old Q.
No there isnt - its been discussed ad nausiam.
do a search.
G-man
BBQ king
- Posts
- 12,065
- Location
- essex.... in the middle somewhere
there is a long term fix for this problem its called buy a defender
Northern Irelander
Well-Known Member
- Posts
- 2,890
- Location
- N. Ireland
I contacted the manufacturers of the silicone fluid, there are two distributors here in the UK.
Haven't priced any yet, but I have a hydragas pump which should displace any of the old fluid. Not sure how I will achieve 84% fill volume lol.
Haven't priced any yet, but I have a hydragas pump which should displace any of the old fluid. Not sure how I will achieve 84% fill volume lol.
- Posts
- 83,232
- Location
- Embasinga stocæ
Tiz easy.
1) measure volume and weight of liquid removed.
2) fill empty VCU with an inert liquid.
3) empty inert liquid and measure volume.
2&3 shud give 100% fill. 1 shud give minimum fill.
4) measure by volume 84% of 2&3 and refill. Or measure equivalent weight to 1 and refill. Or weigh empty VCU and add fluid until yu get a weight of empty VCU please the weight equivalent of 84% volume.
How do you reseal it?
1) measure volume and weight of liquid removed.
2) fill empty VCU with an inert liquid.
3) empty inert liquid and measure volume.
2&3 shud give 100% fill. 1 shud give minimum fill.
4) measure by volume 84% of 2&3 and refill. Or measure equivalent weight to 1 and refill. Or weigh empty VCU and add fluid until yu get a weight of empty VCU please the weight equivalent of 84% volume.
How do you reseal it?
How thick is the body? Plug it and pein it over? Grub screw? braze a patch over the holes?
jonaf
Active Member
- Posts
- 113
- Location
- Sarpsborg, Norway
Thread a grease nipple into the hole and fill the unit with silicone using a grease gun.
Dow Corning can supply the fluid: https://www.xiameter.com/en/Pages/LandingPage.aspx
Dow Corning can supply the fluid: https://www.xiameter.com/en/Pages/LandingPage.aspx
ianda12
Active Member
- Posts
- 837
- Location
- Gravesend, Kent
If the silicon fluid has gone hard and locked the VCU solid (normal fault ) How are you going to get it out ?
- Posts
- 83,232
- Location
- Embasinga stocæ
Tiz a balanced unit, so that might be a problem. How do yu think brazing is going to affect the liquid, or the balance?
Re: viscous coupling
Thread a grease nipple into the hole and fill the unit with silicone using a grease gun.
Dow Corning can supply the fluid: https://www.xiameter.com/en/Pages/LandingPage.aspx
Maybe it was me, but i couldnt see any VCU fluid.
jonaf
Active Member
- Posts
- 113
- Location
- Sarpsborg, Norway
The viscous coupling fluid is in the "Transmission" section on this page: Automotive Solutions - Automotive Lubrication - Dow Corning
ming
SPACE TWOT
- Posts
- 11,977
- Location
- PLANIT ZOG
Ha ha ha ha ha ha. . . . . .OK if any you Muppet's manage to refill a vcu can you monitor it and write details of it on this ear forum even if yer ird or rear bit go's tits 
and if you get it correct we can all save a few bob
and if you get it correct we can all save a few bob 
