Very, very quick welding question.(s)

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
BoxCleva

BoxCleva

New Member
Posts
163
Location
Glyn Ceiriog, North Wales
1) My welder (over the phone) asked what the footwell area was made of. I guessed at mild steel. Am i wrong?

2) The replacement footwells like this one > LAND ROVER SERIES 2 & 3 FOOTWELL REPAIR PANEL L/H (RHD) on eBay (end time 04-Aug-10 16:42:02 BST) , are they bolted in , welded in or both ?

3) Is the area above the door checkstrap bracket an MOT fail ?

The outside upper bulkhead area is sound.

winnywelding.jpg


Thanks :eek:
 
its mild steel although i noticed someone is now making stainless ones....... welded in then things like pedal boxes are bolted to them

i have never known a tester to look at a series check strap as they are not always fitted....... hint hint
 
G-man said:
its mild steel although i noticed someone is now making stainless ones....... welded in then things like pedal boxes are bolted to them

i have never known a tester to look at a series check strap as they are not always fitted....... hint hint
Click to expand...

errm the pop riveted repair patch on the bulkhead won't escape his attention though :rolleyes:
 
I doubt the dodgy repair to the upper part of the bulkhead would cause a fail as long as the door is held on securely and the bulkhead does not flex excessively when the brakes are applied or the steering operated or the steering column yanked around.
 
fenby1976 said:
I doubt the dodgy repair to the upper part of the bulkhead would cause a fail as long as the door is held on securely and the bulkhead does not flex excessively when the brakes are applied or the steering operated or the steering column yanked around.
Click to expand...


Errm what about the "Corrosion within 30cm of a structural, or safety dependant item" rule for MOT testers.
 
fenby1976 said:
I doubt the dodgy repair to the upper part of the bulkhead would cause a fail as long as the door is held on securely and the bulkhead does not flex excessively when the brakes are applied or the steering operated or the steering column yanked around.
Click to expand...

Nope. it definitely doesn't do any of that. I'll get the holes in the footwells sorted and take it for an MOT and see what happens. Thankfully there is so much oil leaking out of the sump gasket all over the chassis it seems to have preserved it ;)
 
The mot man will not like pop rivits if he sees them, I've had things fail with rivets in.
You can if your good weld low grade stainless too mild, 109 stainless will weld to mild with 109L mig wire, if you've done it before.
By the way stainless 'cept for the real expensive marine grade does contain ferrous metal and still rusts away.
 
You must log in or register to reply here.

Similar threads

steve2286w
Rear Axle refurb - welding issue
Replies
18
Views
2K
steve2286w
steve2286w
M
My 1989 90 V8 County
Replies
6
Views
2K
MattYorke
M
Goc3k
Discovery 1 SOLD 1997 300TDI manual D1, Winchester
Replies
16
Views
4K
Goc3k
Goc3k
malcolm_durant
Freelander 1 Storytime: how not to pass your MoT (twice)
Replies
14
Views
3K
ER1C
ER1C
Nodge68
Freelander 2 (LR2) LR trouble codes.
Replies
6
Views
34K
Keith Kernow Kernewick
Keith Kernow Kernewick
Back
Top