hi all , have a fault on suspension Amber/red lean when cornering light, its a L320 4.2 supercharged, have replaced compressor and after having a reader give code C1B14 have also changed lower accelerometer. Have been told now to check voltage .really need some guidance on this all, and any other pointers would be so very much appreciated, thanks all in advance
suspension
- Thread starter Bumble
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Datatek
Well-Known Member
- Posts
- 43,884
- Location
- Near Poitiers SW France
Always worth checking the battery voltage, low volts can throw up many problems
Brand new start stop battery Datatek, last week
tomcat59alan
Well-Known Member
- Posts
- 18,611
- Location
- wirral and triquivijate
Is a start stop battery suitable?
Tom cat, yeh ,had it recommended, and well overspec'd
Datatek
Well-Known Member
- Posts
- 43,884
- Location
- Near Poitiers SW France
Wrong battery unless it's a stop/start Range Rover. Wait a minute, they are mostly stop and no start
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
Having read about, it seems your code is a sensor fault. I take it that is ride height sensor. Have you checked those?
Addit: Found this file which might help
Addit2 @gstuart another DiD for you
Last edited:
Gold rover ,thank you, I have only changed the lower accelerometer, where would I be looking for the other part that is listed on the code?Having read about, it seems your code is a sensor fault. I take it that is ride height sensor. Have you checked those?
Addit: Found this file which might help
Addit2 @gstuart another DiD for you
Luckily have the option to swap it back,was only to see if it was the fault? And apparently not hahWrong battery unless it's a stop/start Range Rover. Wait a minute, they are mostly stop and no start
Datatek
Well-Known Member
- Posts
- 43,884
- Location
- Near Poitiers SW France
You still need to check the voltage at the battery, engine off 12.6 minimum, engine on at 2K rpm over 14 volts.
Thanks for the info ,will do that
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
I have no idea. I found the above by searching around the internet. Maybe @gstuart can help you. Or a wander around the search engines, as I did .
Good luck
gold rover
Well-Known Member
- Posts
- 10,132
- Location
- Scotland,
Maybe search for what you're looking for now, rather than the code you already have?
RangeRoller dt
Well-Sprung Member
- Posts
- 14,255
- Location
- Trapped inside my head @ LZ asylum
Look up exact battery disconnect procedure for your model and follow it to the letter, they can get stroppy. Should follow procedure before changing any electrical
Others here can help more, probably in the searchbar top right corner
Others here can help more, probably in the searchbar top right corner
- Posts
- 12,100
- Location
- Sud ouest France !
Ideally yes, that way there is no risk of spiking it with a 12v current or sultanas..
H
I have RRS 2011 and I’m getting the same code C1B14.
- battery vol is good
- replaced the compressor
- replaced the hight sensors
- tested with new dynamic model
but nothing….
Was thinking next to check all wires and grounding…
@Bumble - Did you resolved your issue?
Thanks
Hi Bumble,
I have RRS 2011 and I’m getting the same code C1B14.
- battery vol is good
- replaced the compressor
- replaced the hight sensors
- tested with new dynamic model
but nothing….
Was thinking next to check all wires and grounding…
@Bumble - Did you resolved your issue?
Thanks
