Other SU components in P38ny components made by SU
- Thread starter EntropyUK
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
- Posts
- 58,170
- Location
- Preston Lancs.
late 70s i believe
I worked on them when they first came out and as said don't recall any Strombergs.
Henry_b
Think outside, no box required.
- Posts
- 15,533
- Location
- somewhere else
- Posts
- 58,170
- Location
- Preston Lancs.
Have same sort of stuff in garage somewhere. It's a big untidy place these days.
The zenith-stromberg 175 cd2s as fitted to my 101V8 have the jet adjustment on the base of the fuel bowl the needle is fixed...
- Posts
- 58,170
- Location
- Preston Lancs.
Henry_b
Think outside, no box required.
- Posts
- 15,533
- Location
- somewhere else
You aren't THAT oldI am old knackered and it was a long time ago.
Just a bit old
Tiny bit
- Posts
- 58,170
- Location
- Preston Lancs.
Different models obviously.
earlier carbs i beleive had a tool to set needle used from top of carb..
- Posts
- 58,170
- Location
- Preston Lancs.
Knew i wasn't going daft. Look at CD3. https://www.howacarworks.com/fuel-systems/adjusting-a-stromberg-carburettor
But were the CD3 fitted to any LR V8...
maybe a time to “hand me down”
I know I am very unlikely to use it this day & age on any I own, but nice to have, if ever 1 comes along
. But the Suck gauge is still handy for the bikeTuning an engine manually and sound is a lost art
J
- Posts
- 58,170
- Location
- Preston Lancs.
That is what i remember about them, but then again i have said it was a long time ago. As said i cannot remember working on a Classic fitted with Strombergs. I only recall SUs.
- Posts
- 58,170
- Location
- Preston Lancs.
maybe a time to “hand me down”
I know I am very unlikely to use it this day & age on any I own, but nice to have, if ever 1 comes along
Tuning an engine manually and sound is a lost art
J
My lad already has most of my tools that's why i took the garage key off him.
Datatek
Well-Known Member
- Posts
- 45,775
- Location
- Near Poitiers SW France
My memory is going to pot, I remember the bottom adjustment from those pictures and something similar on the SU.
The needle adjustment I was thinking about was done with little circlips fitted in grooves in the needle and I think must have been the Delorto carb on the F750 but could have been a motorbike carb.
When i first got the 101as a non-runner with the repair manual everytime i googled for LR V8 carbs only SU came up v,confusing at the time as it didnt match the manual
- Posts
- 58,170
- Location
- Preston Lancs.
Never see a car carb using that method bikes do for sure.
Henry_b
Think outside, no box required.
- Posts
- 15,533
- Location
- somewhere else
SU's are relatively easy to tune and/or rebuild, i find much nicer to work on
These are SU's
These are SU's
- Posts
- 36,270
- Location
- North Shropshire
For a tech nerd i like the old ways. Not completely lostmaybe a time to “hand me down”
I know I am very unlikely to use it this day & age on any I own, but nice to have, if ever 1 comes along
Tuning an engine manually and sound is a lost art
J
Interesting photo H...choke cable doesnt apear to go through carb bracket and there doesnt apear to be a return to tank..
