Freelander 1 Rear wheel cylinder bolts

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
G

guineafowl21

Well-Known Member
Posts
3,352
Location
Inverness
New brake pipes needed all round for MoT, and from bitter experience I’ve ordered all flexi hoses and new wheel cylinders so I can replace the whole lot rather than fighting with crusty unions.

Because the wheel cylinder bolts are often tricky, I ordered four of them too, but they’re out of stock, and this is the case everywhere as far as I can see. Does anyone know of a source of these, or a suitable replacement? PN SMV000010.
 
As Andy said. The bolts are M6 X 10mm long. I use 8.8 grade bolts when I change them, and apply plenty of copper anti-seize. Don't be tempted to use stainless bolts, as they can fail catastrophically.

I grind the head off the old bolts to save messing with them, although space is a bit tight in there.
 
Nodge68 said:
As Andy said. The bolts are M6 X 10mm long. I use 8.8 grade bolts when I change them, and apply plenty of copper anti-seize. Don't be tempted to use stainless bolts, as they can fail catastrophically.

I grind the head off the old bolts to save messing with them, although space is a bit tight in there.
Click to expand...
What tool did you use to cut the bolt heads off? Mine are rounded off so I need to somehow cut them off. As you say, not much room.
 
Hello im planning to replace wheel cylinder, do I also need to change brake pipes as well?
andyfreelandy said:
https://www.ebay.co.uk/itm/FLANGED-HEXAGON-HEAD-BOLTS-FLANGE-HEX-SCREWS-A2-STAINLESS-STEEL-M5-M6-M8-M10/150935671186?ssPageName=STRK:MEBIDX:IT&var=450136610311&_trksid=p2057872.m2749.l2649

M6 x 10mm I think are the ones. Please check though. All sizes available from here.
Click to expand...
Is the M6 x 10mm for the wheel cylinder have 7mm head size? Or does it only matter with the thread size? Mine are rusted and i both need a wrench and maybe new bolts
 
Kalahari_Pete said:
I managed to chisel them off thanks.

does anyone know where I can order online the 4 screws that hold on the rear brake drums?
Click to expand...
When you chiseled them off how did you afterwards get the threads off??
IMG_1577.jpeg
 
The wheel cylinder bolts?
When you chisel them off at the rear, the stud will come out still attached to the wheel cylinder, from the drum side.
 
Freddie17 said:
I only had one stuck and I used a small dremmel wheel on it
Click to expand...
After doing this to the bolt i plan to just keep using the cylinder and hope for the best
IMG_1581.jpeg

IMG_1579.jpeg

image.jpg

Any advice would be good before i put it back together with new shoes and drums
 
Last edited:
You must log in or register to reply here.

Similar threads

Aflyingduckling
Series 3 1983 109 front brake pipe parts
Replies
6
Views
1K
steve2286w
steve2286w
K
What money should I be asking?
2
Replies
27
Views
4K
Karls
K
B
109" Master Cylinder bleeding
2
Replies
30
Views
4K
tottot
tottot
malcolm_durant
Freelander 1 Storytime: how not to pass your MoT (twice)
Replies
14
Views
3K
ER1C
ER1C
D
SWB brakes - master cylinder?
2
Replies
33
Views
2K
DeviousLandyGod
D
Back
Top