Freelander 1 Propshaft carrier bearings - how long to change them? [SOLVED]

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
Kerlaan

Kerlaan

Active Member
Posts
102
Location
Bretagne, France
Hello all

I am stranded in Austria, sort of... (I am taking a few months relaxation here; well that WAS the idea until... :rolleyes: )

I travelled 4000km plus last week returning to the Innsbruck area but in quite a remote location nevertheless. FL1 TD4 2005 manual (275,000km) ran very well as usual, I have excellent MPG. But in the last 1000km hippo developed vibrations that I believe are due to the propshaft carrier bearings failing. Aaaargh... no tools or workshop for the job and so I have to use the nearest Bosch workshop. I can manage with my poor German language skills but this is going to be an adventure... :vb-bomb:

Today I have an inspection ahead of the earliest overhaul appointment first week of August. Question in my head is, "What is the likely time to remove the propshaft assembly to overhaul and refit the bearings"? 3 hours? More?

I am hoping I can have the propshaft removed to protect the other transmission components and run 2WD until August.

And what else needs looking at on the drive train or is good to replace apart from the VCU? My VCU is good.

Thanks for your ideas!
 
Last edited:
Hi,

If you only need to change the bearings, 3 hours should be enought.

A bad VCU can become hot, if it’s bad.

Check the propshaft for cracked rubber first. If the rubber is cracked you will experience knoking sound when changing gears.

There is 3 uv joints that you need to check and replace if needed.

Also the front diff support is know to fail.
 
Last edited:
Alteredtech said:
Hi,

If you only need to change the bearings, 3 hours should be enought.

A bad VCU can become hot, if it’s bad.

Check the propshaft for cracked rubber first. If the rubber is cracked you will experience knoking sound when changing gears.

There is 3 uv joints that you need to check and replace if needed.

Also the front diff support is know to fail.
Click to expand...

Thank you, your point on the front diff support is a useful reminder!! In fact the cost of front and rear diff supports are so low, I think I will instruct new ones all around!

I am about to get underneath and look at the rubbers. Fortunately I have no knocking. Gear changing is super smooth and I have no other transmission strange noise when driving below 30mph

I'm reasonably sure about my VCU and I have even same brand tyres all around and check their pressures 2 to 3 times per week using 2.1bar
 
Grrrr, rear UJ failed (badly) as well as the propshaft carrier bearings... and rear diff seal too!! Diff supports are serviceable still; the rear wetted from the leaking diff seal.

UJ failed video
rear bearing carrier video - front is the same


The VCU looks like it was replaced prior to me having the car 4 years ago (note to self; check the receipts history!)

I shall update the forum with the time and cost as it happens and then mark this as SOLVED, likely 8 August 2024
 
+1 on take prop off & drive it 2WD for now.

Also post your videos on YouTube & link to them using "Insert Media". That way they can be viewed without downloading them from Dropbox !!
1720710505927.png
 
Hi,

According to the video, it safer to remove the prop shaft now. When you remove it, put some align marks just in case.
Get some help to remove it.

It’s better to take GKN at least the UV joints , for the bearings even cheap ones can do the job. You also need new nuts (nylstop) and new spacers.
 
Alteredtech said:
Hi,

According to the video, it safer to remove the prop shaft now. When you remove it, put some align marks just in case.
Get some help to remove it.

It’s better to take GKN at least the UV joints , for the bearings even cheap ones can do the job. You also need new nuts (nylstop) and new spacers.
Click to expand...
Kerlaan said:
Hello all

I am stranded in Austria, sort of... (I am taking a few months relaxation here; well that WAS the idea until... :rolleyes: )

I travelled 4000km plus last week returning to the Innsbruck area but in quite a remote location nevertheless. FL1 TD4 2005 manual (275,000km) ran very well as usual, I have excellent MPG. But in the last 1000km hippo developed vibrations that I believe are due to the propshaft carrier bearings failing. Aaaargh... no tools or workshop for the job and so I have to use the nearest Bosch workshop. I can manage with my poor German language skills but this is going to be an adventure... :vb-bomb:

Today I have an inspection ahead of the earliest overhaul appointment first week of August. Question in my head is, "What is the likely time to remove the propshaft assembly to overhaul and refit the bearings"? 3 hours? More?

I am hoping I can have the propshaft removed to protect the other transmission components and run 2WD until August.

And what else needs looking at on the drive train or is good to replace apart from the VCU? My VCU is good.

Thanks for your ideas!
Click to expand...

FOR INFO - The removal, full overhaul of all propshaft joints, bearings and carriers took 4 hours. A further 2 hours to change the front RHS inner driveshaft boot which had split.

Thanks all!
 
  • Like
Reactions: J_D
You must log in or register to reply here.

Similar threads

M
Propshaft refitting
Replies
4
Views
835
MGT
M
V
Freelander 1 KV6 Vibration
Replies
3
Views
770
Nodge68
Nodge68
M
high pressure fuel pump regulator possible issue after change
Replies
4
Views
1K
MGT
M
S
how to test the gearbox
Replies
6
Views
1K
boguing
boguing
MollyNomad
IRD Bearing/Seal Replacement
Replies
0
Views
844
MollyNomad
MollyNomad
Back
Top