v8250
Well-Known Member
- Posts
- 6,410
- Location
- Deepest Darkest...
@Litch ,thank for this note, I've been thinking of buying these...this is good feedback in understanding how well they work
New Chassis at last for Leaky the Landy - rebuild fred
- Thread starter saxmanuk
- Start date
This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
@Litch ,thank for this note, I've been thinking of buying these...this is good feedback in understanding how well they work
saxmanuk
Active Member
- Posts
- 469
- Location
- On the top of a hill Nr Harrogate
Inspiration indeed - I will look for my local powder coating shop - What was used to media blast ? shot ?
v8250
Well-Known Member
- Posts
- 6,410
- Location
- Deepest Darkest...
I use a superb local media blasting company in Newbury, A&C Shotblasters...I'm guessing they used a softer media rather than hard, so no metal deformation. They work on a lot of Land Rover parts...and there's always a Landy chassis/wheels there. There must be another good Co near Harrogate, or you could always box up and deliver to them. Talk to Craig on 01635.523775
saxmanuk
Active Member
- Posts
- 469
- Location
- On the top of a hill Nr Harrogate
- Posts
- 1,205
- Location
- The Flat lands of Cambridgeshire
they are a good gun, if you find one resisting a bit, then change the battery to full charge
saxmanuk
Active Member
- Posts
- 469
- Location
- On the top of a hill Nr Harrogate
So the better weather has arrived so I have got a little further !
bought a SGS 2 ton crane and engine stand .
bought a SGS 2 ton crane and engine stand .
Litch
Well-Known Member
- Posts
- 2,235
- Location
- Oxfordshire
Yes, the SGS 2T unit is very good, I bought one (and load leveler) for when I did my chassis swop last year.
Served its purpose very well and then I sold it on. Can't see the need to hire one (which means you have to be certain that you will get all jobs done while you have it on hire) as you get most of your money back at the end when a willing buyer takes it off your hands.
Very stable and easy to move even with a heavy load.
I lifted the engine & transmission off the old chassis as a single lump, swung the crane around 180deg and then rolled it forward towards the new chassis. Prior to that I had used it for lifting the new chassis, rotating it for painting, lifting the (fully built-up) bulkhead etc etc.
Served its purpose very well and then I sold it on. Can't see the need to hire one (which means you have to be certain that you will get all jobs done while you have it on hire) as you get most of your money back at the end when a willing buyer takes it off your hands.
Very stable and easy to move even with a heavy load.
I lifted the engine & transmission off the old chassis as a single lump, swung the crane around 180deg and then rolled it forward towards the new chassis. Prior to that I had used it for lifting the new chassis, rotating it for painting, lifting the (fully built-up) bulkhead etc etc.
saxmanuk
Active Member
- Posts
- 469
- Location
- On the top of a hill Nr Harrogate
Looks good ! I got the load leveller too - thanks for the photo tip of the extra strap holding the gearbox etc up as well - will do that.
I am gonna use mine to lift the roof and then also the bulkhead as well - its heavy with all the dash, steering and brake servo etc on it, and the crane lifts high enough to swing it off the old chassis!
cheers
Litch
Well-Known Member
- Posts
- 2,235
- Location
- Oxfordshire
"I am gonna use mine to lift the roof and then also the bulkhead as well - its heavy with all the dash, steering and brake servo etc on it, and the crane lifts high enough to swing it off the old chassis!"
Like this.....
Like this.....
Similar threads
