Hoisting gearbox via centre console question.

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.
B

brianconwy

Well-Known Member
Posts
1,112
Location
conwy, north wales
I want to remove the gearbox on our 2003 td5. I need to drill out rivets to remove a panel by the gearstick. Will removing the round plate surrounding the gearstick itself give enough access for doing this?
Thanks
Brian
 
brianconwy said:
I want to remove the gearbox on our 2003 td5. I need to drill out rivets to remove a panel by the gearstick. Will removing the round plate surrounding the gearstick itself give enough access for doing this?
Thanks
Brian
Click to expand...
Yes it should, I have removed and replaced two D1 manual boxes this way. I did make a small gantry affair that mounts on the front floors just ahead of the fully pushed back seats with a rhs beam that spanned the tranny tunnel to spread the load.
Lifting/supporting was done with a long threaded rod with a short bit of chain attached to the gearbox/transfer case assembly. The threaded rod, (16mm dia) had a nut that sat upon a small thrust bearing on top of and through the spreader making it easy to precisely raise/lower the unit to remove and replace.
After everything is unbolted you only need the front of the vehicle on ramps and a trolley jack to tilt the engine up a bit at the front, once the box is down slide it out the side from beneath.
 
I have bought a second hand engine hoist for lifting and lowering and an engine support beam to support the engine at the right height.

Its good to know that I only have to remove that plate.

Was the one piece of chain enough? You didn't need to attach a chain/sling to the transfer box as well?

Thanks
Brian
 
brianconwy said:
I have bought a second hand engine hoist for lifting and lowering and an engine support beam to support the engine at the right height.

Its good to know that I only have to remove that plate.

Was the one piece of chain enough? You didn't need to attach a chain/sling to the transfer box as well?

Thanks
Brian
Click to expand...
The chain was only 3 or 4 links to attach the threaded rod to a bolt hole at the balance point of the gearbox assembly, all the lifting movement up and down was done with the 16mm nut and about 500 mm of 16mm threaded rod, it gave very precise positioning to extract and instal the gearbox from and to the engine.
The whole load suspended from one point so it was very maneuverable.
Your engine crane in through the door will work ok, but you may need someone to operate the crane, my system enables me to do the whole job single handed, go to woa.
If I was currently at home and I knew how to put photos on here I could show you this simple device I made, it makes the job so easy.
 
brianconwy said:
I have bought a second hand engine hoist for lifting and lowering and an engine support beam to support the engine at the right height.

Its good to know that I only have to remove that plate.

Was the one piece of chain enough? You didn't need to attach a chain/sling to the transfer box as well?

Thanks
Brian
Click to expand...
i remove boxes through the tunnel opening with an engine crane very frequently, i use a chain on the top rhs stud that secures t/box to g/box, its front heavy but very level side ways
 
jamesmartin said:
i remove boxes through the tunnel opening with an engine crane very frequently, i use a chain on the top rhs stud that secures t/box to g/box, its front heavy but very level side ways
Click to expand...
We have the mounts off and have started to tilt the gearbox. How far do we need to tilt? Is there an easy way to remove the plastic sound insulation cover?
 
brianconwy said:
We have the mounts off and have started to tilt the gearbox. How far do we need to tilt? Is there an easy way to remove the plastic sound insulation cover?
Click to expand...
if you have it hanging off the crane lower it down as far as you can ,remove fan cover first, the cover will then easily rotate and out t,whilist its down remove crank sensor and oil pressure connector and top rhs box to engine bolt, raise transmission and from engine bay undo top lh box to engine bolt plus the 8mm headed bolt on that side securing the steel cover plate, then raise the transmission to undo the rest and pull out the box, the good thing about an engine crane is been able to raise /lower the transmission to get better access at different parts
 
jamesmartin said:
if you have it hanging off the crane lower it down as far as you can ,remove fan cover first, the cover will then easily rotate and out t,whilist its down remove crank sensor and oil pressure connector and top rhs box to engine bolt, raise transmission and from engine bay undo top lh box to engine bolt plus the 8mm headed bolt on that side securing the steel cover plate, then raise the transmission to undo the rest and pull out the box, the good thing about an engine crane is been able to raise /lower the transmission to get better access at different parts
Click to expand...
Thanks. I have removed the crank sensor when taking the starter off. Can I do damage by lowering the gearbox too much? We are still trying to remove cover. Thanks again.
 
We have now got the two top bolts off, so wil have a go at this clevis pin. I will try and find the oil pressure connector. How many 8mm bolts are there? I can see one on the passenger side. Thanks
 
You must log in or register to reply here.

Similar threads

B
Blower / Heater Motor squeak-Hum at slow speeds.
Replies
7
Views
592
JohnKeane
J
JockHiltz
Testing glow plugs
Replies
1
Views
1K
miktdish
miktdish
Tango91
  • Poll
Disco 2 Things I wish I knew when I took the body off (99 D2 TD5)
Replies
8
Views
2K
FlatbedPilot
FlatbedPilot
P
Disco 2 Access to the Autobox harness
Replies
3
Views
501
Stanleysteamer
Stanleysteamer
K
What money should I be asking?
2
Replies
20
Views
795
Atomician
Atomician
Back
Top