P38A Got's me some ticking....

This site contains affiliate links for which LandyZone may be compensated if you make a purchase.

Liner or Cam wear?

  • Liner

    Votes: 2 15.4%
  • Cam

    Votes: 3 23.1%
  • Fecked Follower

    Votes: 5 38.5%
  • Tick what tick? Wait, where's me hearing aid?

    Votes: 0 0.0%
  • Who cares? You bought a P38 cheap what do you expect?

    Votes: 3 23.1%

  • Total voters
    13
So, today I spent some time stripping down and getting me bits and bobs out.

Bonnet into service mode....

10.JPG


20.JPG


First point of call was to address the comments on oil pressure - whipped out my hose and adaptors, the realised that getting to the oil pressure switch (which is the easiest place to plug the gauge into) can be a bit of a sod - there is a hard coolant pipe that runs very close to it, the alternator bracket is above it, and trying to get to it from underneath is difficult because of the oil line to the cooler!

Any how, whipped the Alternator and bracket off, got the switch out and put in the pressure gauge

30.JPG


40.JPG


Run the Engine and bled the air out of the line....



So, with good pressure, I proceeded to strip the manifold off.

First, mark up the LPG injectors and harnesses

50.JPG


60.JPG


70.JPG


Removed the gas injector rails, petrol injector splice harness and vaporiser coolant pipes

80.JPG


Then, take all the intake ducting off, remove multiplugs to the throttle pot, IACV - remove the coolant pipes to the body warmer, breather to the rocker cover and the throttle and cruise control cables

90.JPG


100.JPG


Undo the 6 socket cap bolts for the plenum chamber and lift off

110.JPG


Took the passenger side rocker cover off and had a gander - all looks fine under there too - all the rockers are firm, the rods are seated nicley, no play of excessive movement anywhere!

120.JPG


Sooooo, cover back on - time to dig deeper and get the intake manifold off

130.JPG


This is a bit of a faff, but basically, undo the bolts for the injector wiring harness, undo the bolts holding the fuel rail in place and the ignition coil brakcet in place, carefully lift he fuel rail to release the iggy coil bracket. Undo the fuel supply and return pipes from the fuel rail (carefully depressurise the lines first (cover the rail schreider valve with a rag and depress the inner valve.)

Remove the multiplug to the iggy coil, undo the 12 manifold bolts in the published order

160.JPG


Then carefully prise the manifold off the gasket and lift away.

140.JPG


150.JPG


Once I then retreived the iggy coil packs and took the leads off - one post and lead was covered in oxidised corrosion..!!!!

170.JPG


180.JPG


Ah ha....... this probably explains the misifres and popping and backfiring - uneven idle etc etc - but not the ticking!! But it is a step forward!

Pulled the old plugs out and they are fecked - I am surprised the car ran at all

300.JPG


310.JPG


320.JPG


330.JPG


340.JPG


350.JPG


360.JPG


370.JPG




So, with he manifold off, undo the two bolts holding the valley gasket clamps in place and lift off the old valley gasket to reveal the camshaft and followers.

190.JPG


200.JPG


210.JPG


220.JPG


230.JPG


240.JPG


250.JPG


260.JPG


270.JPG


280.JPG


290.JPG




Looking at the lobes and the followers, looking at there movement relative to eachother, there would appear to be no excessive or worrying signs of wear on the cam at all (surprisingly).

So it would initially appear that the ticking may not be due to worn cam lobes or a dicky lifter/follower....thats a bugger!

The ticking/tapping only happens when it gets warm, and that points to potential liner issues...maybe.

Speaking with the other half, she says I have got this far, and to get the heads off, is just faffing with the exhaust manifold and heatsheilds, and then the heads bolts, so I may aswell go the whole hog and lift the heads and look at the gaskets and liners whilst I am there.

But that will have to wait a couple of weeks now as I can only do the work at the weekends, and we are busy with birthdays etc for the next couple!

What are your thoughts peeps??

Watch this space....

Only one thought, should have bought a diesel
 
Ist close up pic of cam lobe looks iffy, but it's prolly just oil, not a flat spot?
I thought that also! I've seen a modern Audi with a completely rounded exhaust cam lobe....you wouldn't think it with more modern materials but then it was produced economically....
Modern shįte....
 
Then rely on oil technology these days. One owner that skips services and its on a slippery slope downhill rapidly.
You've a very good point, the oil in the engine was kinda filthy!!!
And looking at the rest of the cars condition in general.... It may have skipped a lot of general care. Another story.... How goes you wammers?:)
 
The 'Flat Spot' is just a trick of the light - thankfully.

Yes, Lifters were checked while on the flat 'Heel' end of the lobe - obviously!!!

I am still shocked at the state of the plugs....

Heads are to come off after chatting with the other half - we have got this far, may as well for the cost of the new head and exhaust gaskets and bolts. I am just now intrigued by looking at the liners etc.

I already have all the top end gaskets, new front cover gasket, sump gasket, front cover oil seal, rockers, shafts, springs, pedestals etc. Thanks to a kind member on here, a replacement cam.

To get the cam out, you have to remove the front cover, to remove the front cover, you have to remove the sump, and while I am on my back under the car, I may as well look at the big end shells too!!!

Such fun!
 
If you're taking the heads off I've got your tool for the front pulley if you want to borrow it back!

Plus the correct size socket in two depths for tightening the head bolts back up. And a dial gauge and other bits you need for the job. And a proper accurate machined straight edge and feeler gauges to check your head for warp. Cost me a fortune, only used once, and you're welcome to borrow the lot if you need it.

You'll have to speak to @Grrrrrr though, all my tools are at his house for safe keeping whilst I'm away!
 
Last edited:
Back
Top